- 您现在的位置：买卖IC网 > PDF目录79859 > LTC6102CMS (LINEAR TECHNOLOGY CORP) SPECIALTY ANALOG CIRCUIT, PDSO8 PDF资料下载
参数资料
| 型号： | LTC6102CMS |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 模拟信号调理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO8 |
| 封装： | PLASTIC, MSOP-8 |
| 文件页数： | 2/20页 |
| 文件大小： | 257K |
| 代理商： | LTC6102CMS |
LTC6102/LTC6102HV
10
6102fa
APPLICATIONS INFORMATION
Figure 3. Shunt Diode Limits Maximum Input Voltage to Allow
Better Low Input Resolution Without Overranging
Selection of External Input Resistor, RIN
The external input resistor, RIN, controls the transconduc-
tance of the current sense circuit, IOUT = VSENSE/RIN. For
example, if RIN = 100, then IOUT = VSENSE/100 or IOUT =
1mA for VSENSE = 100mV.
Figure 2. Kelvin Input Connection Preserves Accuracy
with Large Load Current and Large Output Current
LTC6102
ROUT
VOUT
6102 F02
RIN
–
V+
LOAD
RSENSE
RIN
+
–
+
V+
–INF
V–
OUT
VREG
0.1μF
TIE AS CLOSE TO RIN AS POSSIBLE
–INS
+IN
LOAD
V+
V–
OUTPUT
RSENSE*
ROUT
LTC6102
RIN
–
RIN
+
CREG
*VISHAY VCS1625 SERIES
WITH 4 PAD KELVIN CONNECTION
V–
V+
LOAD
DSENSE
6102 F03
RSENSE
RIN should be chosen to provide the required resolution
while limiting the output current. At low supply voltage,
IOUT may be as much as 1mA. By setting RIN such that
the largest expected sense voltage gives IOUT = 1mA, then
the maximum output dynamic range is available. Output
dynamic range is limited by both the maximum allowed
output current (Note 1) and the maximum allowed output
voltage, as well as the minimum practical output signal. If
less dynamic range is required, then RIN can be increased
accordingly, reducing the output current and power dis-
sipation. If small sense currents must be resolved ac-
curately in a system that has very wide dynamic range, a
smaller RIN may be used if the max current is limited in
another way, such as with a Schottky diode across RSENSE
(Figure 3). This will reduce the high current measurement
accuracy by limiting the result, while increasing the low
current measurement resolution. This approach can be
helpful in cases where occasional large burst currents
may be ignored.
Care should be taken when designing the PC board lay-
out for RIN, especially for small RIN values. All trace and
interconnect impedances will increase the effective RIN
value, causing a gain error. It is important to note that the
large temperature drift of copper resistance will cause a
change in gain over temperature if proper care is not taken
to reduce this effect.
To further limit the effect of trace resistance on gain,
maximizing the accuracy of these circuits, the LTC6102 has
been designed with a Kelvin input. The inverting terminal
(–INS) is separate from the feedback path (–INF). During
operation, these two pins must be connected together.
The design of the LTC6102 is such that current into –INS
is input bias current only, which is typically 60pA at 25°C.
Almost all of the current from RIN ows into –INF, through
the LTC6102, and into ROUT via the OUT pin. In order to
minimize gain error, –INS should be routed in a separate
path from –INF to a point as close to RIN as possible. In
addition, the higher potential terminal of RIN should be
connected directly to the positive terminal of RSENSE (or
any input voltage source). For the highest accuracy, RIN
should be a four-terminal resistor if it is less than 10Ω.
Selection of External Output Resistor, ROUT
The output resistor, ROUT, determines how the output cur-
rent is converted to voltage. VOUT is simply IOUT ROUT.
In choosing an output resistor, the max output voltage
must rst be considered. If the circuit that is driven by the
output does not have a limited input voltage, then ROUT
相关PDF资料 |
PDF描述 |
|---|---|
| LT3751EFE#TR | 1-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20 |
| LQS100A48-1V2REK | 1-OUTPUT 120 W DC-DC REG PWR SUPPLY MODULE |
| LQS100A48-1V5AK | 1-OUTPUT 150 W DC-DC REG PWR SUPPLY MODULE |
| LQS100A48-1V8REN | 1-OUTPUT 180 W DC-DC REG PWR SUPPLY MODULE |
| LH1901-2R-D4 | 1-OUTPUT AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC6102CMS8#PBF | 功能描述:IC AMP CURRENT SENSE 8-MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Differential Circuit Design Techniques for Communication Applications 标准包装:1 系列:- 放大器类型:RF/IF 差分 电路数:1 输出类型:差分 转换速率:9800 V/µs 增益带宽积:- -3db带宽:2.9GHz 电流 - 输入偏压:3µA 电压 - 输入偏移:- 电流 - 电源:40mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-VQFN 裸露焊盘，CSP 供应商设备封装:16-LFCSP-VQ 包装:剪切带 (CT) 产品目录页面:551 (CN2011-ZH PDF) 其它名称:ADL5561ACPZ-R7CT |
| LTC6102CMS8#TRPBF | 功能描述:IC AMP CURRENT SENSE 8-MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:50 系列:- 放大器类型:通用 电路数:2 输出类型:满摆幅 转换速率:1.8 V/µs 增益带宽积:6.5MHz -3db带宽:4.5MHz 电流 - 输入偏压:5nA 电压 - 输入偏移:100µV 电流 - 电源:65µA 电流 - 输出 / 通道:35mA 电压 - 电源，单路/双路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:10-TFSOP，10-MSOP（0.118"，3.00mm 宽） 供应商设备封装:10-MSOP 包装:管件 |
| LTC6102CMS8-1#PBF | 功能描述:IC AMP CURRENT SENSE 8-MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 产品培训模块:Differential Circuit Design Techniques for Communication Applications 标准包装:1 系列:- 放大器类型:RF/IF 差分 电路数:1 输出类型:差分 转换速率:9800 V/µs 增益带宽积:- -3db带宽:2.9GHz 电流 - 输入偏压:3µA 电压 - 输入偏移:- 电流 - 电源:40mA 电流 - 输出 / 通道:- 电压 - 电源，单路/双路(±):3 V ~ 3.6 V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:16-VQFN 裸露焊盘，CSP 供应商设备封装:16-LFCSP-VQ 包装:剪切带 (CT) 产品目录页面:551 (CN2011-ZH PDF) 其它名称:ADL5561ACPZ-R7CT |
| LTC6102CMS8-1#TRPBF | 功能描述:IC AMP CURRENT SENSE 8-MSOP RoHS:是 类别:集成电路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 标准包装:1 系列:- 放大器类型:通用 电路数:4 输出类型:满摆幅 转换速率:0.6 V/µs 增益带宽积:1MHz -3db带宽:- 电流 - 输入偏压:2pA 电压 - 输入偏移:1000µV 电流 - 电源:85µA 电流 - 输出 / 通道:20mA 电压 - 电源，单路/双路(±):1.8 V ~ 6 V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SOICN 包装:剪切带 (CT) 产品目录页面:680 (CN2011-ZH PDF) 其它名称:MCP6L04T-E/SLCT |
| LTC6102CMS8PBF | 制造商:Linear Technology 功能描述:Zero-Drift curr Sense Amplifier LTC6102 |
发布紧急采购，3分钟左右您将得到回复。