- 您现在的位置：买卖IC网 > PDF目录11022 > LTC6602CUF#TRPBF (Linear Technology)IC FILTER BANDPASS/LOWPASS 24QFN PDF资料下载
参数资料
| 型号： | LTC6602CUF#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 16/28页 |
| 文件大小： | 0K |
| 描述： | IC FILTER BANDPASS/LOWPASS 24QFN |
| 标准包装： | 2,500 |
| 滤波器类型： | 带通 |
| 频率 - 截止或中心： | 300kHz |
| 滤波器数： | 2 |
| 滤波器阶数： | 5th |
| 电源电压： | 2.7 V ~ 3.6 V |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-WFQFN 裸露焊盘 |
| 供应商设备封装： | 24-QFN 裸露焊盘（4x4） |
| 包装： | 带卷 (TR) |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
LTC6602
23
6602fc
APPLICATIONS INFORMATION
The LTC6602, an Adaptable Baseband Filter for an
RFID Reader
Aradio-frequencyidentification(RFID)systemisanauto-id
technology that identifies any object that contains a coded
tag. An RFID system consists of a reader (or interrogator)
and a tag. An RFID system capable of identifying multiple
tags at a maximum operating distance operates in the
UHF frequency range. A UHF reader transmits informa-
tion to a tag by modulating an RF signal in the 860MHz
to 960MHz frequency range. Typically a tag is passive,
meaning that it receives all of its operating energy from a
reader that transmits a continuous wave (CW) RF signal
to power a tag. A tag responds by modulating the reflec-
tion coefficient of its antenna, thereby backscattering an
information signal to the reader. Reliable detection of a
tag signal requires communication protocols that define
the physical and operating interaction between readers
and tags. The latest UHF RFID protocol, the Electronic
ProductCode(EPC)globalclass-1generation2standard
(C1G2), have been accepted worldwide and is also known
as ISO 18000-6C. The C1G2 standard defines a reader to
tag and a tag to reader communication using a flexible
set of signal modulation, data encoding, data rates and
command procedures. C1G2 specifies reader and tag data
symbols using pulse-interval encoding. Tag signal detec-
tion requires measuring the time interval between signal
transitions (a data “1” symbol has a longer interval than
a data “0” symbol). The reader initiates a tag inventory by
sending a signal that instructs a tag to set its backscatter
data rate and encoding. C1G2 certified RFID readers can
operate in an RF environment where many readers are in
closeproximity.ThethreeoperatingmodesofC1G2,single
interrogator, multiple interrogator and dense interrogator,
define the spectral limits of reader and tag signals for an
optimum balance of reliable multitag detection and high
data throughput (for more information on C1G2, consult
the references at the end of this design note). The advan-
tages of C1G2 complex protocols can be realized by using
a reader whose receiver contains a high linearity direct
conversion I and Q demodulator, a low noise amplifier, a
dual baseband filter with variable gain and bandwidth and
a dual analog to digital converter (ADC).
Certified C1G2 UHF RFID readers can adapt to a great
variety of operating conditions. To achieve operating
flexibility a reader’s baseband circuits must include an
adaptable bandwidth filter. Figure 17 shows an LTC6602
based filter circuit that uses SPI control to vary the filter’s
bandwidthtoadjustfortheC1G2complexsetofdatarates,
encoding and modulation. The filter’s clock frequency is
set by the SPI control of 8-bit LTC2630 DAC (digital to
analog converter). The DAC voltage through a resistive
divider sets the current into the LTC6602 RBIAS pin. The
resistive divider sets the clock frequency range for a DAC
voltage range 0V to 3V. For the resistor values in Figure 17
(191k and 61.9k) the clock frequency range is 40MHz to
100MHz (234.4kHz per bit). The lowpass and highpass
division ratio is set by the SPI control of the LTC6602. The
cutoff range for the highpass filter is 6.7kHz to 100kHz and
for the lowpass filter is 66.7kHz to 1MHz. The optimum
filter bandwidth setting can be adjusted by a software
algorithm and is a function of the reader’s data clock, data
rate, encoding and modulation. The filter bandwidth must
be sufficiently narrow to maximize the dynamic range to
the ADC input and wide enough to preserve signal transi-
tions and pulse width. If the filter setting is optimum then
a DSP algorithm can reliably detect tag data. Figure 18a
shows the filter’s time response to a typical tag symbol
sequence (a “short” pulse interval followed by a “long”
pulse interval). The lowpass cutoff frequency is set equal
to the reciprocal of the shortest interval (fCUTOFF = 1/10s
= 100kHz). If the lowpass cutoff frequency is lower the
signal transition and time interval will be distorted beyond
recognition by any tag signal detection algorithm. The set-
ting of the highpass cutoff frequency is more qualitative
thanspecific.Thehighpasscutofffrequencymustbelower
than the reciprocal of the longest interval (for Figure 18
example, highpass fCUTOFF < 1/20s < 50kHz) and as
high as possible to decrease the receiver’s low frequency
noise (baseband amplifier and down-converted phase and
amplitude noise). Figures 18a and 18b show the filter’s
total response (lowpass plus highpass filter). The filter’s
output is shown with 30kHz and a 10kHz highpass cutoff
frequency setting. Comparing the filter outputs with a
10kHz and a 30kHz highpass setting, the signal transitions
and time intervals of the 10kHz output are adequate for
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1061CSW#TRPBF | IC FILTR BUILDNG BLK TRPL 20SOIC |
| LTC1061CSW#TR | IC BUILDING BLK TRPL FLTR 20SOIC |
| LTC1061CSW#PBF | IC FILTR BUILDNG BLK TRPL 20SOIC |
| LTC1164-6CN | IC FILTR 8TH ORDER LOWPASS 14DIP |
| LTC1562ACG#TR | IC FILTER UNIV RC QUAD LN 20SSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC6602IUF#PBF | 功能描述:IC FILTER BANDPASS/LOWPASS 24QFN RoHS:是 类别:集成电路 (IC) >> 接口 - 滤波器 - 有源 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 滤波器类型:连续时间，带通低通 频率 - 截止或中心:150kHz 滤波器数:4 滤波器阶数:8th 电源电压:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) |
| LTC6602IUF#TRPBF | 功能描述:IC FILTER BANDPASS/LOWPASS 24QFN RoHS:是 类别:集成电路 (IC) >> 接口 - 滤波器 - 有源 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1,000 系列:- 滤波器类型:连续时间，带通低通 频率 - 截止或中心:150kHz 滤波器数:4 滤波器阶数:8th 电源电压:4.74 V ~ 11 V，±2.37 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:28-SOIC（0.295"，7.50mm 宽） 供应商设备封装:28-SOIC W 包装:带卷 (TR) |
| LTC6602IUF-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Matched, High Frequency Bandpass/Lowpass Filters |
| LTC6602IUF-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Matched, High Frequency Bandpass/Lowpass Filters |
| LTC6603 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual Adjustable Lowpass Filter |
发布紧急采购，3分钟左右您将得到回复。