- 您现在的位置：买卖IC网 > PDF目录9464 > LTC6900IS5#TRPBF (Linear Technology)IC OSC SILICON 20MHZ TSOT23-5 PDF资料下载
参数资料
| 型号： | LTC6900IS5#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/12页 |
| 文件大小： | 0K |
| 描述： | IC OSC SILICON 20MHZ TSOT23-5 |
| 标准包装： | 2,500 |
| 类型： | 振荡器 - 硅 |
| 频率： | 1kHz ~ 20MHz |
| 电源电压： | 2.7 V ~ 5.5 V |
| 电流 - 电源： | 920µA |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | SOT-23-5 细型，TSOT-23-5 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | TSOT-23-5 |
| 安装类型： | 表面贴装 |
LTC6900
5
6900fa
PIN FUNCTIONS
V+ (Pin 1): Voltage Supply (2.7V ≤ V+ ≤ 5.5V). This supply
must be kept free from noise and ripple. It should be by-
passed directly to a ground plane with a 0.1μF capacitor.
GND (Pin 2): Ground. Should be tied to a ground plane
for best performance.
SET (Pin 3): Frequency-Setting Resistor Input. The value
of the resistor connected between this pin and V+ deter-
mines the oscillator frequency. The voltage on this pin is
held by the LTC6900 to approximately 1.1V below the V+
voltage. For best performance, use a precision metal lm
resistor with a value between 10kΩ and 2MΩ and limit
the capacitance on this pin to less than 10pF.
DIV (Pin 4): Divider-Setting Input. This three-state input
selects among three divider settings, determining the value
of N in the frequency equation. Pin 4 should be tied to GND
for the ÷1 setting, the highest frequency range. Floating
Pin 4 divides the master oscillator by 10. Pin 4 should be
tied to V+ for the ÷100 setting, the lowest frequency range.
To detect a oating DIV pin, the LTC6900 attempts to pull
the pin toward midsupply. Therefore, driving the DIV pin
high requires sourcing approximately 2μA. Likewise, driv-
ing DIV low requires sinking 2μA. When Pin 4 is oated,
it should preferably be bypassed by a 1nF capacitor to
ground or it should be surrounded by a ground shield to
prevent excessive coupling from other PCB traces.
OUT (Pin 5): Oscillator Output. This pin can drive 5kΩ and/
or 10pF loads. Heavier loads may cause inaccuracies due
to supply bounce at high frequencies. Voltage transients,
coupled into Pin 5, above or below the LTC6900 power
supplies will not cause latchup if the current into/out of
the OUT pin is limited to 50mA.
BLOCK DIAGRAM
–
+
1
3
GAIN = 1
V+
VBIAS
IRES
RSET
SET
GND
PATENT PENDING
MASTER OSCILLATOR
PROGRAMMABLE
DIVIDER (N)
(÷1, 10 OR 100)
VRES = (V
+ – VSET) = 1.1V TYPICALLY
IRES
(V+ – VSET)
MO = 10MHz 20kΩ
THREE-STATE
INPUT DETECT
GND
V+
2μA
6900 BD
2μA
OUT
DIVIDER
SELECT
5
DIV
4
2
+
–
+
–
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1799IS5#TRPBF | IC OSC SILICON 33MHZ TSOT23-5 |
| MAX1270ACAI+T | IC ADC 12BIT SERIAL 28-SSOP |
| MAX186CEWP+T | IC ADC 12BIT SERIAL 20-SOIC |
| MAX1340BETX+ | IC ADC/DAC 12BIT W/FIFO 36WQFN |
| LTC6904IMS8#TR | IC OSC SILICON 68MHZ 8MSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC6902 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Multiphase Oscillator with Spread Spectrum Frequency Modulation |
| LTC6902CMS | 功能描述:IC OSC SILICON 20MHZ 10MSOP RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 可编程计时器和振荡器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:45 系列:- 类型:温度 - 补偿晶体振荡器（TCXO） 计数:- 频率:25MHz 电源电压:3.135 V ~ 3.465 V 电流 - 电源:1.5mA 工作温度:-40°C ~ 85°C 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 包装:管件 供应商设备封装:16-SOIC W 安装类型:表面贴装 |
| LTC6902CMS#PBF | 功能描述:IC OSC SILICON 20MHZ 10MSOP RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 可编程计时器和振荡器 系列:- 标准包装:3,000 系列:- 类型:振荡器 - 晶体 计数:- 频率:- 电源电压:2.3 V ~ 5.5 V 电流 - 电源:1.07mA 工作温度:-30°C ~ 80°C 封装/外壳:SOT-665 包装:带卷 (TR) 供应商设备封装:SS迷你型-5D 安装类型:表面贴装 其它名称:AN8955SSMTXLTR |
| LTC6902CMS#PBF | 制造商:Linear Technology 功能描述:Programmable Oscillator IC |
| LTC6902CMS#TR | 功能描述:IC OSC SILICON 20MHZ 10MSOP RoHS:否 类别:集成电路 (IC) >> 时钟/计时 - 可编程计时器和振荡器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:45 系列:- 类型:温度 - 补偿晶体振荡器（TCXO） 计数:- 频率:25MHz 电源电压:3.135 V ~ 3.465 V 电流 - 电源:1.5mA 工作温度:-40°C ~ 85°C 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 包装:管件 供应商设备封装:16-SOIC W 安装类型:表面贴装 |
发布紧急采购，3分钟左右您将得到回复。