参数资料
| 型号： | LTC6907IS6#TRPBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/12页 |
| 文件大小： | 0K |
| 描述： | IC OSC SILICON 4MHZ TSOT23-6 |
| 标准包装： | 2,500 |
| 类型： | 振荡器 - 硅 |
| 频率： | 40kHz ~ 4MHz |
| 电源电压： | 3 V ~ 3.6 V |
| 电流 - 电源： | 305µA |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | SOT-23-6 细型，TSOT-23-6 |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | TSOT-23-6 |
| 安装类型： | 表面贴装 |
LTC6907
5
6907fa
–
+
4
6
1
OP AMP
fOSC
150
DRIVER
fOSC
IFB
OUT
6907 BD
3
DIV
PROGRAMMABLE
DIVIDER (n)
(
÷1, ÷3, ÷10)
THREE-LEVEL
INPUT
DETECTOR
VOLTAGE
CONTROLLED
OSCILLATOR
(MASTER OSCILLATOR)
SET
V+
2
GND
VSET VGRD 650mV
ISET = IFB
FREQUENCY-TO-CURRENT
CONVERTERS
BUFFER
GRD
RSET
5M
DIVIDER
SELECT
V+
VSET
5
fOSC = 4MHz
50k
RSET
UU
U
PI FU CTIO S
OUT (Pin 1): Oscillator Output. The OUT pin swings from
GND to V+ with an output resistance of approximately
150
. For micropower operation, the load resistance
must be kept as high as possible and the load capacitance
as low as possible.
GND (Pin 2): Ground.
DIV (Pin 3): Divider Setting Input. This three-level input
selects one of three internal digital divider settings, deter-
mining the value of N in the frequency equation. Tie to GND
for
÷1, leave floating for ÷3 and tie to V+ for ÷10. When left
floating, the LTC6907 pulls Pin 3 to mid-supply with a
2.5M resistor. When Pin 3 is floating, care should be taken
to reduce coupling from the OUT pin and its trace to Pin 3.
Coupling can be reduced by increasing the physical space
between traces or by shielding the DIV pin with grounded
metal.
SET (Pin 4): Frequency Setting Resistor Input. Connect a
resistor, RSET, from this pin to GND to set the oscillator
frequency. For best performance use a precision metal or
thin-film resistor of 0.1% or better tolerance and 50ppm/
°C
or better temperature coefficient. For lower accuracy
applications, an inexpensive 1% thick-film resistor may be
used. Limit the capacitance in parallel with RSET to less
than 10pF to reduce jitter and to ensure stability. The
voltage on the SET pin is approximately 650mV at 25
°C
and decreases with temperature by about –2.3mV/
°C.
GRD (Pin 5): Guard Signal. This pin can be used to reduce
PC board leakage across the frequency setting resistor,
RSET. The GRD pin is held within a few millivolts of the SET
pin and shunts leakage current away from the SET pin. To
control leakage, connect a bare copper trace (a trace with
no solder mask) to GRD and loop it around the SET pin and
all PC board metal connected to SET. Careful attention to
board layout and assembly can prevent leakage currents.
The use of a guard ring provides additional shielding of
leakage currents from the SET pin and is optional. If
unused, the GRD pin should be left unconnected.
V+ (Pin 6): Voltage Supply (3V to 3.6V). A 0.1
F
decoupling capacitor should be placed as close as pos-
sible to this pin for best performance.
BLOCK DIAGRA
W
相关PDF资料 |
PDF描述 |
|---|---|
| LTC6906IS6#TRPBF | IC OSC SILICON 1MHZ TSOT23-6 |
| AD974AN | IC DAS 16BIT 4CH 200KSPS 28-DIP |
| V28A12M200BG2 | CONVERTER MOD DC/DC 12V 200W |
| AD974AR | IC DAS 16BIT 4CH 200KSPS 28-SOIC |
| LTC6907IS6#TRMPBF | IC OSC SILICON 4MHZ TSOT23-6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC6908-1 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Resistor Set SOT-23 Oscillator with Spread Spectrum Modulation |
| LTC6908-2 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Resistor Set SOT-23 Oscillator with Spread Spectrum Modulation |
| LTC6908CDCB-1 | 制造商:Linear Technology 功能描述:Silicon Oscillator 6-Pin DFN EP |
| LTC6908CDCB-1#PBF | 制造商:Linear Technology 功能描述: 制造商:Linear Technology 功能描述:SC-Timing, Cut Tape 2 Phase 10kHz - 10MHz Oscillator W/SSFM |
| LTC6908CDCB-1#TRMPBF | 功能描述:IC OSC SILICON 10MHZ 6-DFN RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 可编程计时器和振荡器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:45 系列:- 类型:温度 - 补偿晶体振荡器（TCXO） 计数:- 频率:25MHz 电源电压:3.135 V ~ 3.465 V 电流 - 电源:1.5mA 工作温度:-40°C ~ 85°C 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 包装:管件 供应商设备封装:16-SOIC W 安装类型:表面贴装 |
发布紧急采购，3分钟左右您将得到回复。