- 您现在的位置：买卖IC网 > PDF目录15325 > LTC690IN8 (Linear Technology)IC MPU SUPERVISORY CIRCUIT 8-DIP PDF资料下载
参数资料
| 型号： | LTC690IN8 |
| 厂商： | Linear Technology |
| 文件页数： | 6/20页 |
| 文件大小： | 0K |
| 描述： | IC MPU SUPERVISORY CIRCUIT 8-DIP |
| 标准包装： | 50 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 低有效 |
| 复位超时： | 最小为 35 ms |
| 电压 - 阀值： | 4.65V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
LTC690/LTC691
LTC694/LTC695
BLOCK DIAGRAM
VBATT
VCC
–
+
C2
M2
M1
CHARGE
PUMP
VOUT
BATT ON
LOW?LINE
1.3V
+
C1
–
CE OUT
CE IN
GND
PFI
OSC IN
OSC SEL
WDI
–
+
OSC
TRANSITION
DETECTOR
C3
RESET PULSE
GENERATOR
WATCHDOG
TIMER
PFO
RESET
RESET
WDO
690 BD
PIN FUNCTIONS
V CC : 5V Supply Input. The V CC pin should be bypassed
with a 0.1μF capacitor.
V OUT : Voltage Output for Backed Up Memory. Bypass with
a capacitor of 0.1μF or greater. During normal operation,
V OUT obtains power from V CC through an NMOS power
switch, M1, which can deliver up to 50mA and has a typical
on resistance of 5Ω. When V CC is lower than V BATT , V OUT
is internally switched to V BATT . If V OUT and V BATT are not
used, connect V OUT to V CC .
V BATT : Back-Up Battery Input. When V CC falls below V BATT ,
auxiliary power, connected to V BATT , is delivered to V OUT
through PMOS switch, M2. If back-up battery or auxiliary
power is not used, V BATT should be connected to GND.
GND: Ground pin.
BATT ON: Battery On Logic Output from Comparator C2.
BATT ON goes low when V OUT is internally connected to
V CC . The output typically sinks 35mA and can provide
base drive for an external PNP transistor to increase the
output current above the 50mA rating of V OUT . BATT ON
goes high when V OUT is internally switched to V BATT .
PFI: Power Failure Input. PFI is the noninverting input
to the power-fail comparator, C3. The inverting input is
internally connected to a 1.3V reference. The power failure
output remains high when PFI is above 1.3V and goes
low when PFI is below 1.3V. Connect PFI to GND or V OUT
when C3 is not used.
690ff
6
For more information www.linear.com/690
相关PDF资料 |
PDF描述 |
|---|---|
| B41043A3687M | 680UF 10V 8X20 SINGLE END |
| B41043A2108M | 1000UF 6.3V 10X20 SINGLE END |
| ECC60DJWB | CONN EDGECARD 120PS .100 PRESSFT |
| LTC1147CS8-5#TRPBF | IC REG CTRLR BUCK PWM CM 8-SOIC |
| LTC2914CDHC-1#TRPBF | IC VOLT MONITOR QUAD 16-DFN |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC690IN8#PBF | 功能描述:IC MPU SUPERVISORY CIRCUIT 8-DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| LTC690IN8PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Microprocessor Supervisory Circuits |
| LTC690IN8-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Microprocessor Supervisory Circuits |
| LTC690IS8 | 功能描述:IC MPU SUPERVISORY CIRCUIT 8SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| LTC690IS8#PBF | 功能描述:IC MPU SUPERVISORY CIRCUIT 8SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
发布紧急采购，3分钟左右您将得到回复。