- 您现在的位置：买卖IC网 > PDF目录15344 > LTC694CN8 (Linear Technology)IC MPU SUPERVISORY CIRCUIT 8-DIP PDF资料下载
参数资料
| 型号： | LTC694CN8 |
| 厂商： | Linear Technology |
| 文件页数： | 11/20页 |
| 文件大小： | 0K |
| 描述： | IC MPU SUPERVISORY CIRCUIT 8-DIP |
| 标准包装： | 50 |
| 类型： | 简单复位/加电复位 |
| 监视电压数目： | 1 |
| 输出： | 开路漏极或开路集电极 |
| 复位： | 高有效/低有效 |
| 复位超时： | 最小为 140 ms |
| 电压 - 阀值： | 4.65V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 通孔 |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-PDIP |
| 包装： | 管件 |
LTC690/LTC691
LTC694/LTC695
APPLICATIONS INFORMATION
If battery connections are made through long wires, a
10Ω to 100Ω series resistor and a 0.1μF capacitor are
recommended to prevent any overshoot beyond V CC due
to the lead inductance (Figure 4).
input of battery-backed up CMOS RAM. CE OUT can also
be used to drive the Store or Write input of an EEPROM,
EAROM or NOVRAM to achieve similar protection. Figure
5 shows the timing diagram of CE IN and CE OUT.
10
4.3M
0.1μF
V BATT
LTC690
LTC691
LTC694
LTC695
GND
CE IN can be derived from the microprocessor’s address
decoder output. Figure 6 shows a typical nonvolatile CMOS
RAM application.
Memory protection can also be achieved with the LTC690
and LTC694 by using RESET as shown in Figure 7.
690 F04
Table 1. Input and Output Status in Battery Back-Up Mode
Figure 4. 10Ω/0.1μF Combination Eliminates Inductive
Overshoot and Prevents Spurious Resets During Battery
Replacement
Table 1 shows the state of each pin during battery back-up.
When the battery switchover section is not used, connect
V BATT to GND and V OUT to V CC .
SIGNAL
V CC
V OUT
V BATT
BATT ON
PFI
PFO
STATUS
C2 monitors V CC for active switchover.
V OUT is connected to V BATT through an internal PMOS switch.
The supply current is 1μA maximum.
Logic high. The open-circuit output voltage is equal to V OUT .
Power failure input is ignored.
Logic low
Memory Protection
The LTC691 and LTC695 include memory protection cir-
cuitry that ensures the integrity of the data in memory by
preventing write operations when V CC is at invalid level.
Two additional pins, CE IN and CE OUT, control the Chip
Enable or Write inputs of CMOS RAM. When V CC is 5V,
CE OUT follows CE IN with a typical propagation delay of
20ns. When V CC falls below the reset voltage threshold or
V BATT , CE OUT is forced high, independent of CE IN. CE
OUT is an alternative signal to drive the CE , CS , or Write
RESET Logic low
RESET Logic high. The open-circuit output voltage is equal to V OUT .
LOW?LINE Logic low
WDI Watchdog input is ignored.
WDO Logic high. The open-circuit output voltage is equal to V OUT .
CE IN Chip?Enable Input is ignored.
CE OUT Logic high. The open-circuit output voltage is equal to V OUT .
OSC IN OSC IN is ignored.
OSC SEL OSC SEL is ignored.
V CC
V1
V2
V1 = RESET VOLTAGE THRESHOLD
V2 = RESET VOLTAGE THRESHOLD +
RESET THRESHOLD HYSTERESIS
CE IN
CE OUT
V OUT = V BATT
Figure 5. Timing Diagram for CE IN and CE OUT
V OUT = V BATT
690 F05
690ff
For more information www.linear.com/690
11
相关PDF资料 |
PDF描述 |
|---|---|
| ECC40DCAH-S189 | CONN EDGECARD 80POS R/A .100 SLD |
| LTC3805HMSE-5#TRPBF | IC REG CTRLR BST FLYBK CM 10MSOP |
| RMC15DREN-S13 | CONN EDGECARD 30POS .100 EXTEND |
| VE-2WR-EW-F4 | CONVERTER MOD DC/DC 7.5V 100W |
| VE-2WR-EW-F3 | CONVERTER MOD DC/DC 7.5V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC694CN8#PBF | 功能描述:IC MPU SUPERVISORY CIRCUIT 8-DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 其它有关文件:STM6717 View All Specifications 标准包装:1 系列:- 类型:多压监控器 监视电压数目:2 输出:开路漏极或开路集电极 复位:低有效 复位超时:最小为 600 ms 电压 - 阀值:1.11V，3.075V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:SC-74A，SOT-753 供应商设备封装:SOT-23-5 包装:Digi-Reel® 产品目录页面:1194 (CN2011-ZH PDF) 其它名称:497-7019-6 |
| LTC694CN8-3.3 | 功能描述:IC MPU SUPRVISRY CIRC 3.3V 8-DIP RoHS:否 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| LTC694CN8-3.3#PBF | 功能描述:IC MPU SUPRVISRY CIRC 3.3V 8-DIP RoHS:是 类别:集成电路 (IC) >> PMIC - 监控器 系列:- 标准包装:1 系列:- 类型:简单复位/加电复位 监视电压数目:1 输出:开路漏极或开路集电极 复位:高有效 复位超时:- 电压 - 阀值:1.8V 工作温度:-40°C ~ 125°C 安装类型:表面贴装 封装/外壳:6-TSOP（0.059"，1.50mm 宽）5 引线 供应商设备封装:5-TSOP 包装:剪切带 (CT) 其它名称:NCP301HSN18T1GOSCT |
| LTC694CN8PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Microprocessor Supervisory Circuits |
| LTC694CN8-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:Microprocessor Supervisory Circuits |
发布紧急采购，3分钟左右您将得到回复。