- 您现在的位置：买卖IC网 > PDF目录79697 > LTC6992IDCB6-4#TRPBF (LINEAR TECHNOLOGY CORP) SWITCHING CONTROLLER, PDSO6 PDF资料下载
参数资料
| 型号： | LTC6992IDCB6-4#TRPBF |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING CONTROLLER, PDSO6 |
| 封装： | 2 X 3 MM, LEAD FREE, PLASTIC, MO-229TBD, DFN-6 |
| 文件页数： | 11/32页 |
| 文件大小： | 322K |
| 代理商： | LTC6992IDCB6-4#TRPBF |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页当前第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页
LTC6992-1/LTC6992-2/
LTC6992-3/LTC6992-4
19
69921234p
Basic Operation
The simplest and most accurate method to program the
LTC6992 is to use a single resistor, RSET, between the
SET and GND pins. The design procedure is a four step
process. After choosing the POL bit setting and proper
LTC6992 version, select the NDIV value and then calculate
the value for the RSET resistor.
Step 1: Selecting the POL Bit Setting
Most applications will use POL = 0, resulting in a positive
transfer function. However, some applications may require a
negative transfer function, where increasing VMOD reduces
the output duty cycle. For example, if the LTC6992 is used
in a feedback loop, POL = 1 may be required to achieve
negative feedback.
Step 2: Selecting the LTC6992 Version
The difference between the LTC6992 versions is observed
at the endpoints of the duty cycle control range. Applica-
tions that require the output never stop oscillating should
use the LTC6992-2. If it is better to allow the output to
rest at GND or V+ (0% or 100% duty cycle, respectively),
select the LTC6992-1.
The LTC6992-3 and LTC6992-4 clamp the duty cycle at
only one end of the control range, allowing the output to
stop oscillating at the other extreme. If POL = 1 the clamp
will swap from low duty cycle to high, or vice-versa. Refer
to Table 2 and Figure 4 for assistance in selecting the
proper version.
Step 3: Selecting the NDIV Frequency Divider Value
As explained earlier, the voltage on the DIV pin sets the
DIVCODE which determines both the POL bit and the
NDIV value. For a given output frequency, NDIV should be
selected to be within the following range.
62.5kHz
fOUT
≤ NDIV ≤
1MHz
fOUT
(1a)
To minimize supply current, choose the lowest NDIV value
(generally recommended). For faster start-up or decreased
jitter, choose a higher NDIVsetting.Alternatively,useTable1
as a guide to select the best NDIV value for the given ap-
plication.
APPLICATIONS INFORMATION
With POL already chosen, this completes the selection of
DIVCODE. Use Table 1 to select the proper resistor divider
or VDIV/V+ ratio to apply to the DIV pin.
Step 4: Calculate and Select RSET
The final step is to calculate the correct value for RSET
using the following equation.
RSET =
1MHz 50k
NDIV fOUT
(1b)
Select the standard resistor value closest to the calculated
value.
Example: Design a PWM circuit that satisfies the following
requirements:
fOUT = 20kHz
Positive VMOD to duty cycle response
Output can reach 100% duty cycle, but not 0%
Minimum power consumption
Step 1: Selecting the POL Bit Setting
For positive transfer function (duty cycle increases with
VMOD), choose POL = 0.
Step 2: Selecting the LTC6992 Version
To limit the minimum duty cycle, but allow the maximum
duty cycle to reach 100%, choose LTC6992-4. (Note that
if POL = 1 the LTC6992-3 would be the correct choice.)
Step 3: Selecting the NDIV Frequency Divider Value
Choose an NDIV value that meets the requirements of
Equation (1a).
3.125 ≤ NDIV ≤ 50
Potential settings for NDIV include 4 and 16. NDIV = 4 is
the best choice, as it minimizes supply current by us-
ing a large RSET resistor. POL = 0 and NDIV = 4 requires
DIVCODE = 1. Using Table 1, choose the R1 and R2 values
to program DIVCODE = 1.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC1174CN8-3.3#TR | 1 A SWITCHING REGULATOR, 200 kHz SWITCHING FREQ-MAX, PDIP8 |
| LT8410IDC#TRPBF | 0.03 A SWITCHING REGULATOR, PDSO8 |
| LM2576HVBT | 3.5 A SWITCHING REGULATOR, 52 kHz SWITCHING FREQ-MAX, PSFM5 |
| LWT-30H-522 | 3-OUTPUT 30 W AC-DC REG PWR SUPPLY MODULE |
| LNS-Z-5-OV | 1-OUTPUT 14 W AC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTC6992IS6-1#PBF | 制造商:Linear Technology 功能描述:TIMERBLOX: VOLTAGE-CONTROLLED PULSE WIDTH MODULATOR (PWM) 制造商:Linear Technology 功能描述:Bulk 制造商:Linear Technology 功能描述:OSCILLATOR 1MHZ 5.5V TSOT-2 制造商:Linear Technology 功能描述:OSCILLATOR, 1MHZ, 5.5V, TSOT-23-6; Operating Mode:-; Frequency:1MHz; Supply Voltage Min:2.25V; Supply Voltage Max:5.5V; Digital IC Case Style:TSOT-23; No. of Pins:6; Clock External Input:Yes; Operating Temperature Min:-40C ;RoHS Compliant: Yes |
| LTC6992IS6-1#TRMPBF | 功能描述:IC OSC SILICON 1MHZ TSOT23-6 RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 可编程计时器和振荡器 系列:TimerBlox® 标准包装:3,000 系列:- 类型:振荡器 - 晶体 计数:- 频率:- 电源电压:2.3 V ~ 5.5 V 电流 - 电源:1.07mA 工作温度:-30°C ~ 80°C 封装/外壳:SOT-665 包装:带卷 (TR) 供应商设备封装:SS迷你型-5D 安装类型:表面贴装 其它名称:AN8955SSMTXLTR |
| LTC6992IS6-1#TRPBF | 功能描述:IC OSC SILICON 1MHZ TSOT23-6 RoHS:是 类别:集成电路 (IC) >> 时钟/计时 - 可编程计时器和振荡器 系列:TimerBlox® 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:45 系列:- 类型:温度 - 补偿晶体振荡器（TCXO） 计数:- 频率:25MHz 电源电压:3.135 V ~ 3.465 V 电流 - 电源:1.5mA 工作温度:-40°C ~ 85°C 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 包装:管件 供应商设备封装:16-SOIC W 安装类型:表面贴装 |
| LTC6992IS6-1-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:TimerBlox Voltage-Controlled Pulse Width Modulator (PWM) |
| LTC6992IS6-1-TRPBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:TimerBlox Voltage-Controlled Pulse Width Modulator (PWM) |
发布紧急采购，3分钟左右您将得到回复。