- 您现在的位置：买卖IC网 > PDF目录45000 > LTM4601AHVMPV (LINEAR TECHNOLOGY CORP) SWITCHING REGULATOR, PBGA133 PDF资料下载
参数资料
| 型号： | LTM4601AHVMPV |
| 厂商： | LINEAR TECHNOLOGY CORP |
| 元件分类： | 稳压器 |
| 英文描述： | SWITCHING REGULATOR, PBGA133 |
| 封装： | 15 X 15 MM, 2.82 MM HEIGHT, LEAD FREE, LGA-133 |
| 文件页数： | 28/30页 |
| 文件大小： | 519K |
| 代理商： | LTM4601AHVMPV |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页当前第28页第29页第30页
LTM4601AHV
7
4601ahvfb
(See Package Description for Pin Assignment)
VIN (Bank 1): Power Input Pins. Apply input voltage be-
tween these pins and PGND pins. Recommend placing
input decoupling capacitance directly between VIN pins
and PGND pins.
VOUT (Bank 3): Power Output Pins. Apply output load
between these pins and PGND pins. Recommend placing
outputdecouplingcapacitancedirectlybetweenthesepins
and PGND pins. See Figure 17.
PGND (Bank 2): Power ground pins for both input and
output returns.
VOSNS– (Pin M12): (–) Input to the Remote Sense Ampli-
fier. This pin connects to the ground remote sense point.
The remote sense amplifier is used for VOUT ≤3.3V. Tie to
INTVCC if not used.
VOSNS+ (Pin J12): (+) Input to the Remote Sense Ampli-
fier. This pin connects to the output remote sense point.
The remote sense amplifier is used for VOUT ≤3.3V. Tie to
GND if not used.
DIFFVOUT (Pin K12): Output of the Remote Sense Ampli-
fier. This pin connects to the VOUT_LCL pin. Leave floating
if remote sense amplifier is not used.
DRVCC (Pin E12): This pin normally connects to INTVCC
for powering the internal MOSFET drivers. This pin can
be biased up to 6V from an external supply with about
50mA capability, or an external circuit shown in Figure 18.
This improves efficiency at the higher input voltages by
reducing power dissipation in the module.
INTVCC (Pin A7, D9): This pin is for additional decoupling
of the 5V internal regulator. These pins are internally con-
nected. Pin A7 is a test pin.
PLLIN (Pin A8): External Clock Synchronization Input to
the Phase Detector. This pin is internally terminated to
SGND with a 50k resistor. Apply a clock with high level
above2VandbelowINTVCC.SeeApplicationsInformation.
TRACK/SS(PinA9):OutputVoltageTrackingandSoft-Start
Pin. When the module is configured as a master output,
then a soft-start capacitor is placed on this pin to ground to
control the master ramp rate. A soft-start capacitor can be
used for soft-start turn on as a stand alone regulator. Slave
operation is performed by putting a resistor divider from
the master output to ground, and connecting the center
pointofthedividertothispin.SeeApplicationsInformation.
MPGM (Pins A12, B11): Programmable Margining Input.
A resistor from this pin to ground sets a current that is
equal to 1.18V/R. This current multiplied by 10kΩ will
equal a value in millivolts that is a percentage of the 0.6V
referencevoltage.SeeApplicationsInformation.Toparallel
LTM4601AHVs,eachrequiresanindividualMPGMresistor.
Do not tie MPGM pins together. Both pins are internally
connected. Pin A12 is a test pin.
fSET (Pins B12, C11): Frequency Set Internally to 850kHz.
An external resistor can be placed from this pin to ground
to increase frequency. See Applications Information for
frequency adjustment. Both pins are internally connected.
Pin B12 is a test pin.
VFB (Pin F12): The Negative Input of the Error Amplifier.
Internally, this pin is connected to VOUT_LCL pin with a
60.4k precision resistor. Different output voltages can be
programmed with an additional resistor between VFB and
SGND pins. See Applications Information.
MARG0 (Pin C12): This pin is the LSB logic input for the
margining function. Together with the MARG1 pin it will
determine if margin high, margin low or no margin state
is applied. The pin has an internal pull-down resistor of
50k. See Applications Information.
MARG1 (Pin D12): This pin is the MSB logic input for the
margining function. Together with the MARG0 pin it will
determine if margin high, margin low or no margin state
is applied. The pin has an internal pull-down resistor of
50k. See Applications Information.
SGND (Pins H12, H11, G11): Signal Ground. These pins
connect to PGND at output capacitor point. See Figure 17.
pin FuncTions
相关PDF资料 |
PDF描述 |
|---|---|
| LTM4601AHVY | SWITCHING REGULATOR, PBGA133 |
| LTM8052EV#PBF | SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PBGA81 |
| LTM8052IV#PBF | SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PBGA81 |
| LTM8062EV#PBF | BATTERY CHARGE CONTROLLER, 1150 kHz SWITCHING FREQ-MAX, PBGA77 |
| LTM8062AEV#PBF | BATTERY CHARGE CONTROLLER, 1150 kHz SWITCHING FREQ-MAX, PBGA77 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTM4601AHVMPV#3DJPBF | 制造商:Linear Technology 功能描述:DC to DC Converter and Switching Regulator Chip 制造商:LINEAR_TECH 功能描述: |
| LTM4601AHVMPV#PBF | 功能描述:IC DC/DC UMODULE 12A 133-LGA RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:µModule® 设计资源:Maxi/Mini/Micro Design Guide, Appl Manual 标准包装:1 系列:微型 类型:隔离 输出数:1 电压 - 输入（最小）:18V 电压 - 输入（最大）:36V Voltage - Output 1:48V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:100W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:模块 尺寸/尺寸:2.28" L x 1.45" W x 0.62" H（57.9mm x 36.8mm x 15.7mm） 包装:散装 工作温度:-20°C ~ 100°C 效率:* 电源（瓦特）- 最大:* 其它名称:1102-1290V24C48C100BL-ND |
| LTM4601AHVMPV#PBF | 制造商:Linear Technology 功能描述:DC/DC Converter IC |
| LTM4601AHVMPV-PBF | 制造商:LINER 制造商全称:Linear Technology 功能描述:12A, 28VIN DC/DC μModule with PLL, Output Tracking and Margining |
| LTM4601AHVMPY#PBF | 功能描述:IC DC/DC UMODULE 12A 133-BGA RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:µModule® 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:66V 电压 - 输入（最大）:160V Voltage - Output 1:12V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:50W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9-FinMod 尺寸/尺寸:4.60" L x 1.86" W x 0.79" H（116.8mm x 47.2mm x 20.1mm） 包装:散装 工作温度:-25°C ~ 85°C 效率:* 电源（瓦特）- 最大:* |
发布紧急采购，3分钟左右您将得到回复。