- 您现在的位置：买卖IC网 > Datasheet目录868 > LTM4615IV#PBF (Linear Technology)IC SWIT REG BUCK 4A ADJ 144LGA Datasheet资料下载
参数资料
| 型号： | LTM4615IV#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 8/24页 |
| 文件大小： | 0K |
| 描述： | IC SWIT REG BUCK 4A ADJ 144LGA |
| 产品培训模块： | LTM4615 - Triple Output, Low Voltage DC/DC µModule Regulator Power Module vs. Discrete DC to DC |
| 软件下载： | LTM4615 |
| 产品目录绘图： | LTM Series_15x15x2.8 |
| 设计资源： | DC1367A Design Files LTM4615IV#PBF Footprint.bxl |
| 特色产品： | LTM4615 Series μModule Products DC/DC μModule Regulator Family |
| 标准包装： | 119 |
| 系列： | µModule® |
| 类型： | 非隔离（POL） |
| 输出数： | 3 |
| 电压 - 输入（最小）： | 2.38V |
| 电压 - 输入（最大）： | 5.5V |
| Voltage - Output 1： | 0.8 ~ 5 V |
| Voltage - Output 2： | 0.8 ~ 5 V |
| Voltage - Output 3： | 0.4 ~ 2.6 V |
| 电流 - 输出（最大）： | 4A，4A，1.5A |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 144-LGA |
| 尺寸/尺寸： | 0.59" L x 0.59" W x 0.11" H（15.0mm x 15.0mm x 2.8mm） |
| 包装： | 托盘 |
| 工作温度： | -40°C ~ 125°C |
| 效率： | 95% |
| 产品目录页面： | 2711 (CN2011-ZH PDF) |
| 配用： | DC1367A-ND - BOARD EVAL LTM4615 |
LTM4615
PIN FUNCTIONS
V IN1 , V IN2 (J1-J5, K1-K5); (C1-C6, D1-D5): Power Input
Pins. Apply input voltage between these pins and GND
pins. Recommend placing input decoupling capacitance
directly between V IN pins and GND pins.
V OUT1 , V OUT2 (K9-K12, L9-L12, M9-M12); (C9-C12,
D9-D12, E11-E12): Power Output Pins. Apply output load
between these pins and GND pins. Recommend placing
output decoupling capacitance directly between these pins
and GND pins. Review Table 4.
GND1, GND2, (H1, H7-H12, J6-J12, K6-K8 L1, L7-L8,
M1-M8); (A1-A12, B1, B7-B12, C7-C8, D6-D8, E1,
E8-E10): Power Ground Pins for Both Input and Output
Returns.
TRACK1, TRACK2 (L3, E3): Output Voltage Tracking Pins.
When the module is configured as a master output, then a
soft-start capacitor is placed on the RUN/SS pin to ground
to control the master ramp rate, or an external ramp can
be applied to the master regulator’s track pin to control it.
Slave operation is performed by putting a resistor divider
from the master output to ground, and connecting the
center point of the divider to this pin on the slave regulator.
If tracking is not desired, then connect the TRACK pin to
V IN . Load current must be present for tracking. See the
Applications Information section.
FB1, FB2 (L6, E6): The Negative Input of the Switching
Regulators’ Error Amplifier. Internally, these pins are con-
nected to V OUT with a 4.99k precision resistor. Different
output voltages can be programmed with an additional
resistor between the FB and GND pins. Two power modules
can current share when this pin is connected in parallel
with the adjacent module’s FB pin. See the Applications
Information section.
FB3 (F6): The Negative Input of the LDO Error Amplifier.
Internally the pin is connected to LDO_OUT with a 4.99k
resistor. Different output voltages can be programmed with
an additional resistor between the FB3 and GND pins. See
the Applications Information section.
COMP1, COMP2 (L5, E5): Current Control Threshold
and Error Amplifier Compensation Point. The current
comparator threshold increases with this control voltage.
Two power modules can current share when this pin is
connected in parallel with the adjacent module’s COMP
pin. Each channel has been internally compensated. See
the Applications Information section.
PGOOD1, PGOOD2 (L4, E4): Output Voltage Power
Good Indicator. Open-drain logic output that is pulled to
ground when the output voltage is not within ±7.5% of
the regulation point.
RUN/SS1, RUN/SS2 (L2, E2): Run Control and Soft-Start
Pin. A voltage above 0.8V will turn on the module, and
below 0.5V will turn off the module. This pin has a 1M
resistor to V IN and a 1000pF capacitor to GND. See the
Applications Information section for soft-start information.
SW1, SW2 (H2-H6, B2-B6): The switching node of the
circuit is used for testing purposes. This can be connected
to copper on the board for improved thermal performance.
SW1 and SW2 must be floating on separate copper planes.
LDO_IN (G1-G4): VLDO Input Power Pins. Place input
capacitor close to these pins.
LDO_OUT (G9-G12): VLDO Output Power Pins. Place
output capacitor close to these pins. Minimum 1mA load
is necessary for proper output voltage accuracy.
BOOST3 (E7): Boost Supply for Driving the Internal VLDO
NMOS Into Full Enhancement. The pin is use for testing
the internal boost converter. The output is typically 5V.
GND3 (F1-F5, F7, F9-F12, G6-G8): The power ground pins
for both input and output returns for the internal VLDO.
PGOOD3 (G5): VLDO Power Good Pin.
EN3 (F8): VLDO Enable Pin.
8
For more information www.linear.com/LTM4615
4615fb
相关PDF资料 |
PDF描述 |
|---|---|
| LTM4618IV#PBF | IC DC-DC UMODULE BUCK 6A 84-LGA |
| LTM4619IV#PBF | IC SWIT REG BUCK 4A ADJ 144LGA |
| LTM4627MPY#PBF | IC DC/DC UMODULE 15A 133-BGA |
| LTM4628EV#PBF | IC DC/DC UMODULE 16A 144-LGA |
| LTM8008HV#PBF | IC DC/DC UMODULE 16-LGA |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTM4616 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Low VIN, 8A DC/DC μModule Regulator |
| LTM4616_12 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Dual 8A per Channel Low VIN DC/DC μModule Regulator |
| LTM4616EV#PBF | 功能描述:IC DC/DC UMODULE DUAL 8A 144-LGA RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:µModule® 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:66V 电压 - 输入（最大）:160V Voltage - Output 1:12V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:50W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9-FinMod 尺寸/尺寸:4.60" L x 1.86" W x 0.79" H（116.8mm x 47.2mm x 20.1mm） 包装:散装 工作温度:-25°C ~ 85°C 效率:* 电源（瓦特）- 最大:* |
| LTM4616EV#PBF | 制造商:Linear Technology 功能描述:DC/DC Controller LTC |
| LTM4616EVPBF | 制造商:Linear Technology 功能描述:Conv DC-DC Dual-Out Step Down |
发布紧急采购，3分钟左右您将得到回复。