参数资料
型号: LTM8025EV#PBF
厂商: Linear Technology
文件页数: 12/22页
文件大小: 0K
描述: IC CONVERTER BUCK 3A ADJ 70LGA
产品培训模块: LTM8025 - 36VIN, 3A Step Down Regulator
High Voltage µModule DC/DC Regulators
Power Module vs. Discrete DC to DC
软件下载: LTM8025 Spice Model
产品目录绘图: LTM Series_15x15x4.3
设计资源: DC1379A Design Files
LTM8025EV#PBF Footprint.bxl
特色产品: LTM8025 Series
μModule Products
标准包装: 170
系列: µModule®
类型: 非隔离(POL)
输出数: 1
电压 - 输入(最小): 3.6V
电压 - 输入(最大): 36V
Voltage - Output 1: 0.8 ~ 24 V
电流 - 输出(最大): 3A
安装类型: 表面贴装
封装/外壳: 70-LGA
尺寸/尺寸: 0.59" L x 0.35" W x 0.17" H(15.0mm x 9.0mm x 4.3mm)
包装: 托盘
工作温度: -40°C ~ 125°C
产品目录页面: 2711 (CN2011-ZH PDF)
配用: DC1379A-ND - BOARD EVAL LTM8025
LTM8025
APPLICATIONS INFORMATION
Table 2. Switching Frequency vs R T Value
SWITCHING FREQUENCY
0.2MHz
0.3MHz
0.4MHz
0.5MHz
0.6MHz
0.7MHz
0.8MHz
0.9MHz
1MHz
1.2MHz
1.4MHz
1.6MHz
1.8MHz
2MHz
2.2MHz
2.4MHz
R T VALUE
215kΩ
137kΩ
100kΩ
76.8kΩ
63.4kΩ
52.3kΩ
44.2kΩ
38.3kΩ
34.0kΩ
26.7kΩ
21.5kΩ
17.8kΩ
14.7kΩ
12.1kΩ
9.76kΩ
8.25kΩ
voltage, output voltage and switching frequency, but 4V to
5V works well in many applications. In all cases, ensure
that the maximum voltage at the BIAS pin is less than 25V
and that the sum of V IN and BIAS is less than 56V. If BIAS
power is applied from a remote or noisy voltage source, it
may be necessary to apply a decoupling capacitor locally
to the pin.
Load Sharing
Two or more LTM8025’s may be paralleled to produce higher
currents. To do this, tie the V IN , ADJ, V OUT and SHARE
pins of all the paralleled LTM8025’s together. To ensure
that paralleled modules start up together, the RUN/SS pins
may be tied together, as well. If the RUN/SS pins are not
tied together, make sure that the same valued soft-start
capacitors are used for each module. Current sharing can
be improved by synchronizing the LTM8025s. An example
of two LTM8025s configured for load sharing is given in
the Typical Applications section.
Operating Frequency Tradeoffs
It is recommended that the user apply the optimal R T
value given in Table 1 for the input and output operating
condition. System level or other considerations, however,
may necessitate another operating frequency. While the
LTM8025 is flexible enough to accommodate a wide range
of operating frequencies, a haphazardly chosen one may
result in undesirable operation under certain operating or
fault conditions. A frequency that is too high can reduce
efficiency, generate excessive heat or even damage the
LTM8025 if the output is overloaded or short circuited. A
frequency that is too low can result in a final design that has
too much output ripple or too large of an output capacitor.
BIAS Pin Considerations
The BIAS pin is used to provide drive power for the in-
ternal power switching stage and operate other internal
circuitry. For proper operation, it must be powered by at
least 2.8V. If the output voltage is programmed to 2.8V
or higher, BIAS may be simply tied to AUX. If V OUT is less
than 2.8V, BIAS can be tied to V IN or some other voltage
source. If the BIAS pin voltage is too high, the efficiency
of the LTM8025 may suffer. The optimum BIAS voltage is
dependent upon many factors, such as load current, input
Burst Mode Operation
To enhance efficiency at light loads, the LTM8025 auto-
matically switches to Burst Mode operation which keeps
the output capacitor charged to the proper voltage while
minimizing the input quiescent current. During Burst Mode
operation, the LTM8025 delivers single cycle bursts of
current to the output capacitor followed by sleep periods
where the output power is delivered to the load by the output
capacitor. In addition, V IN and BIAS quiescent currents are
each reduced to microamps during the sleep time. As the
load current decreases towards a no load condition, the
percentage of time that the LTM8025 operates in sleep
mode increases and the average input current is greatly
reduced, resulting in higher efficiency.
Burst Mode operation is enabled by tying SYNC to GND.
To disable Burst Mode operation, tie SYNC to a stable
voltage above 0.7V. Do not leave the SYNC pin floating .
Minimum Input Voltage
The LTM8025 is a step-down converter, so a minimum
amount of headroom is required to keep the output in
regulation. In addition, the input voltage required to turn
on is higher than that required to run, and depends upon
8025fc
12
For more information www.linear.com/LTM8025
相关PDF资料
PDF描述
LC4064B-75TN100I IC CPLD 64MACROCELLS 100TQFP
ISL61852DIRZ-T IC USB PWR CTRLR DUAL 8DFN
VE-B54-CY-F4 CONVERTER MOD DC/DC 48V 50W
VE-B54-CY-F3 CONVERTER MOD DC/DC 48V 50W
M4A3-64/64-7VNI IC CPLD ISP 4A 64MC 100TQFP
相关代理商/技术参数
参数描述
LTM8025EY#PBF 制造商:Linear Technology 功能描述:DC/DC CONVERTER 0.8-24V 72W 制造商:Linear Technology 功能描述:BUCK UMODULE 36VIN 3A LGA- 制造商:Linear Technology 功能描述:BUCK, UMODULE, 36VIN, 3A, LGA-70 制造商:Linear Technology 功能描述:DC-DC REGULATOR, BUCK, ADJ, BGA-70, Primary Input Voltage:36V, No. of Outputs:1, Output Current:3A, No. of Pins:70, Operating Temperature Min:-40C, Operating Temperature Max:125C, MSL:MSL 3 - 168 hours, Package / Case:70-BGA , RoHS Compliant: Yes
LTM8025IV 制造商:LINER 制造商全称:Linear Technology 功能描述:36V, 3A Step-Down μModule Converter
LTM8025IV#PBF 功能描述:IC CONVERTER BUCK 3A ADJ 70LGA RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:µModule® 特色产品:VYB Series High Efficiency Converters 3D 型号:VYB15W-Q48-S15 标准包装:63 系列:V-Infinity VYB15W 类型:隔离 输出数:1 电压 - 输入(最小):18V 电压 - 输入(最大):75V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出(最大):1A 电源(瓦) - 制造商系列:15W 电压 - 隔离:1.5kV(1500V) 特点:具有远程开/关功能和 UVLO 安装类型:通孔 封装/外壳:6-DIP 模块 尺寸/尺寸:2.00" L x 1.00" W x 0.44" H(50.8mm x 25.4mm x 11.3mm) 包装:管件 工作温度:-40°C ~ 85°C 效率:85% 电源(瓦特)- 最大:15W 其它名称:102-2329656-91325R
LTM8025IV#PBF 制造商:Linear Technology 功能描述:BUCK MICROMODULE CONVERTER 制造商:Linear Technology 功能描述:IC, STEP-DOWN MODULE CONVERTER, LGA-70
LTM8025IVPBF 制造商:Linear Technology 功能描述:36V 3A Step-Down uModule Regulator LGA70