- 您现在的位置：买卖IC网 > PDF目录22127 > LTM8026IV#PBF (Linear Technology)IC UMODULE REGULATOR 36VIN 5A PDF资料下载
参数资料
| 型号： | LTM8026IV#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 15/26页 |
| 文件大小： | 0K |
| 描述： | IC UMODULE REGULATOR 36VIN 5A |
| 产品培训模块： | LTM8026 and LTM8052 Step-Down uModule Regulators |
| 标准包装： | 119 |
| 系列： | µModule® |
LTM8026
APPLICATIONS INFORMATION
may be set from 100kHz to 1MHz. The internal oscillator
may also be synchronized to an external clock through
the SYNC pin. The external clock applied to the SYNC pin
must have a logic low below 0.6V and a logic high greater
than 1.2V. The input frequency must be 20% higher than
the frequency determined by the resistor at the RT pin.
In general, the duty cycle of the input signal should be
greater than 10% and less than 90%. Input signals outside
of these specified parameters may cause erratic switching
behavior and subharmonic oscillations. The SYNC pin must
be tied to GND if the synchronization to an external clock
is not required. When SYNC is grounded, the switching
frequency is determined by the resistor at the RT pin. At
light loads, the LTM8026 will enter discontinuous opera-
tion to improve efficiency even while a valid clock signal
is applied to the SYNC pin.
Soft-Start
The soft-start function controls the slew rate of the power
supply output voltage during start-up. A controlled output
voltage ramp minimizes output voltage overshoot, reduces
inrush current from the V IN supply, and facilitates supply
sequencing. A capacitor connected from the SS pin to
GND programs the slew rate. The capacitor is charged
from an internal 11μA current source to produce a ramped
output voltage.
Load Current Derating Using the CTL_T Pin
In high current applications, derating the maximum current
based on operating temperature may prevent damage
to the load. In addition, many applications have thermal
limitations that will require the regulated current to be
reduced based on the load and/or board temperature. To
achieve this, the LTM8026 uses the CTL_T pin to reduce
the effective regulated current in the load. While CTL_I
programs the regulated current in the load, CTL_T can
be configured to reduce this regulated current based
on the analog voltage at the CTL_T pin. The load/board
temperature derating is programmed using a resistor
divider with a temperature dependant resistance (Figure?2).
When the board/load temperature rises, the CTL_T voltage
will decrease. To reduce the regulated current, the CTL_T
voltage must be lower than the voltage at the CTL_I pin.
CTL_T may be higher than CTL_I, but then it will have
no effect.
Voltage Regulation and Output Overvoltage Protection
The LTM8026 uses the ADJ pin to regulate the output
voltage and to provide a high speed overvoltage lockout
to avoid high voltage conditions. If the output voltage
exceeds 125% of the regulated voltage level (1.5V at the
ADJ pin), the LTM8026 terminates switching and shuts
Maximum Output Current Adjust
V REF
2V
I MAX
Amps
7.467 ? R2
R1 + R2
Toadjusttheregulatedloadcurrent,ananalogvoltageis
applied to the CTL_I pin or CTL_T pins. Varying the voltage
between 0V and 1.5V adjusts the maximum current between
the minimum and the maximum current, 5.6A typical.
Graphs of the output current vs CTL_I and CTL_T volt-
ages are given in the Typical Performance Characteristics
section. The LTM8026 provides a 2V reference voltage for
conveniently applying resistive dividers to set the current
limit. The current limit can be set as shown in Figure 1
with the following equation:
=
LTM8026 R1
CTL_I OR CTL_T
R2
8026 F01
Figure 1. Setting the Output Current Limit, I MAX
R V
V REF
R2 LTM8026 R NTC R NTC R X R NTC R NTC
CTL_T
R1 A B C
(OPTION A TO D)
D
R V
R X
8026 F02
Figure 2. Load Current Derating vs Temperature Using NTC
Resistor
8026fb
For more information www.linear.com/LTM8026
15
相关PDF资料 |
PDF描述 |
|---|---|
| RCM12DRMN | CONN EDGECARD 24POS .156 WW |
| LC4064C-75T44C | IC PLD 64MC 30I/O 7.5NS 44TQFP |
| TPME108M004R0018 | CAP TANT 1000UF 4V 20% 2917 |
| VE-2WK-CY-F2 | CONVERTER MOD DC/DC 40V 50W |
| VE-2WK-CY-F1 | CONVERTER MOD DC/DC 40V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTM8026MPV#PBF | 功能描述:IC UMODULE 36VIN 5A CVCC 81LGA RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:* 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:18V 电压 - 输入（最大）:36V Voltage - Output 1:5.8V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:75W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9 针法兰半砖电源模块 尺寸/尺寸:2.28" L x 2.40" W x 0.50" H（57.9mm x 61.0mm x 12.7mm） 包装:散装 工作温度:-10°C ~ 100°C 效率:* 电源（瓦特）- 最大:* |
| LTM8027 | 制造商:LINER 制造商全称:Linear Technology 功能描述:60V、4A DC/DC μModule 穩壓器 |
| LTM8027EV | 制造商:LINER 制造商全称:Linear Technology 功能描述:60V, 4A DC/DC Module Regulator |
| LTM8027EV#PBF | 功能描述:IC BUCK SYNC ADJ 4A 113LGA RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:µModule® 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:66V 电压 - 输入（最大）:160V Voltage - Output 1:12V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:50W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9-FinMod 尺寸/尺寸:4.60" L x 1.86" W x 0.79" H（116.8mm x 47.2mm x 20.1mm） 包装:散装 工作温度:-25°C ~ 85°C 效率:* 电源（瓦特）- 最大:* |
| LTM8027EV#PBF | 制造商:Linear Technology 功能描述:DC/DC Converter IC 制造商:Linear Technology 功能描述:IC, STEP-DOWN DC/DC MODULE REG, LGA-113 |
发布紧急采购，3分钟左右您将得到回复。