- 您现在的位置：买卖IC网 > PDF目录22066 > LTM8031IV#PBF (Linear Technology)IC BUCK ADJ 1A 71LGA PDF资料下载
参数资料
| 型号： | LTM8031IV#PBF |
| 厂商： | Linear Technology |
| 文件页数： | 14/22页 |
| 文件大小： | 0K |
| 描述： | IC BUCK ADJ 1A 71LGA |
| 产品培训模块： | Power Module vs. Discrete DC to DC µModule® Family of EN55022 Class B Certified Regulators |
| 软件下载： | LTM8031 Spice Model |
| 产品目录绘图： | LTM Series_9x15x2.8 |
| 设计资源： | DC1597A Design Files LTM8031IV#PBF Footprint.bxl |
| 特色产品： | μModule Products |
| 标准包装： | 170 |
| 系列： | µModule® |
| 类型： | 非隔离（POL） |
| 输出数： | 1 |
| 电压 - 输入（最小）： | 3.6V |
| 电压 - 输入（最大）： | 36V |
| Voltage - Output 1： | 0.8 ~ 10 V |
| 电流 - 输出（最大）： | 1A |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 71-LGA |
| 尺寸/尺寸： | 0.59" L x 0.35" W x 0.11" H（15.0mm x 9.0mm x 2.8mm） |
| 包装： | 托盘 |
| 工作温度： | -40°C ~ 125°C |
| 产品目录页面： | 2711 (CN2011-ZH PDF) |
| 配用： | DC1597A-ND - BOARD EVAL LTM8031 |
LTM8031
APPLICATIONS INFORMATION
rings as high as 35V and the input current peaks at 20A.
One method of damping the tank circuit is to add another
capacitor with a series resistor to the circuit, as shown
in Figure 4b. A 0.7Ω resistor is added in series with the
input to eliminate the voltage overshoot (it also reduces
the peak input current). A 0.1μF capacitor improves high
frequency filtering. For high input voltages its impact on
efficiency is minor, reducing efficiency less than one-half
percent for a 5V output at full load operating from 24V.
By far the most popular method of controlling overshoot
is shown in Figure 4c, where an aluminum electrolytic
capacitor has been connected to FIN. This capacitor’s high
equivalent series resistance damps the circuit and elimi-
nates the voltage overshoot. The extra capacitor improves
low frequency ripple filtering and can slightly improve the
efficiency of the circuit, though it is likely to be the largest
component in the circuit. Placing the electrolytic capacitor
at the FIN terminals can also improve the LTM8031’s EMI
filtering as well as guard against overshoots caused by
the Q of the integrated filter.
Thermal Considerations
The LTM8031 output current may need to be derated if it is
required to operate in a high ambient temperature or deliver
a large amount of continuous power. The amount of current
derating is dependent upon the input voltage, output power
and ambient temperature. The temperature rise curves
given in the Typical Performance Characteristics section
can be used as a guide. These curves were generated by a
LTM8031 mounted to a 35cm 2 4-layer FR4 printed circuit
board. Boards of other sizes and layer count can exhibit
different thermal behavior, so it is incumbent upon the user
to verify proper operation over the intended system’s line,
load and environmental operating conditions.
The junction-to-air and junction-to-board thermal resis-
tances given in the Pin Configuration diagram may also be
used to estimate the LTM8031 internal temperature. These
thermal coefficients are determined per JESD 51-9 (JEDEC
standard, test boards for area array surface mount package
thermal measurements) through analysis and physical
correlation. Bear in mind that the actual thermal resistance
of the LTM8031 to the printed circuit board depends upon
the design of the circuit board. The die temperature of
the LTM8031 must be lower than the maximum rating of
125°C, so care should be taken in the layout of the circuit
to ensure good heat sinking of the LTM8031.
The bulk of the heat flow out of the LTM8031 is through the
bottom of the module and the LGA pads into the printed
circuit board. Consequently a poor printed circuit board
design can cause excessive heating, resulting in impaired
performance or reliability. Please refer to the PCB Layout
section for printed circuit board design suggestions.
Finally, be aware that at high ambient temperatures the
internal Schottky diode will have significant leakage current
increasing the quiescent current of the LTM8031.
8031fb
14
相关PDF资料 |
PDF描述 |
|---|---|
| VI-272-CY-F4 | CONVERTER MOD DC/DC 15V 50W |
| TAP335M020CCS | CAP TANT 3.3UF 20V 20% RADIAL |
| TPME476K035R0065 | CAP TANT 47UF 35V 10% 2917 |
| RSO-1209S | CONV DC/DC 1W 9-18VIN 09VOUT |
| GMC40DRXH-S734 | CONN EDGECARD 80POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LTM8031MPV#PBF | 功能描述:IC DC-DC UMODULE 1A LN 71LGA RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:µModule® 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:21V 电压 - 输入（最大）:32V Voltage - Output 1:5V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:100W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9-SlimMod 尺寸/尺寸:4.60" L x 1.80" W x 0.52" H（116.8mm x 45.7mm x 13.2mm） 包装:散装 工作温度:-25°C ~ 85°C 效率:* 电源（瓦特）- 最大:* |
| LTM8032 | 制造商:LINER 制造商全称:Linear Technology 功能描述:Ultralow Noise EMC Compliant 36V, 2A DC/DC μModule |
| LTM8032EV#PBF | 功能描述:IC UMODULE DC/DC ULN 2A 71-LGA RoHS:是 类别:电源 - 板载 >> DC DC Converters 系列:µModule® 特色产品:VYB Series High Efficiency Converters 3D 型号:VYB15W-Q48-S15 标准包装:63 系列:V-Infinity VYB15W 类型:隔离 输出数:1 电压 - 输入（最小）:18V 电压 - 输入（最大）:75V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:1A 电源（瓦） - 制造商系列:15W 电压 - 隔离:1.5kV（1500V） 特点:具有远程开/关功能和 UVLO 安装类型:通孔 封装/外壳:6-DIP 模块 尺寸/尺寸:2.00" L x 1.00" W x 0.44" H（50.8mm x 25.4mm x 11.3mm） 包装:管件 工作温度:-40°C ~ 85°C 效率:85% 电源（瓦特）- 最大:15W 其它名称:102-2329656-91325R |
| LTM8032EV#PBF | 制造商:Linear Technology 功能描述:DC/DC odule IC 制造商:Linear Technology 功能描述:BUCK DC/DC MODULE REGULATOR, 200KHZ TO 2.4MHZ, LGA |
| LTM8032EVPBF | 制造商:Linear Technology 功能描述:Ultralow Noise 36V 2A DC/DC UModule |
发布紧急采购，3分钟左右您将得到回复。