- 您现在的位置：买卖IC网 > PDF目录39437 > LV71081E (SANYO SEMICONDUCTOR CO LTD) SPECIALTY CONSUMER CIRCUIT, PQFP100 PDF资料下载
参数资料
| 型号： | LV71081E |
| 厂商： | SANYO SEMICONDUCTOR CO LTD |
| 元件分类： | 消费家电 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PQFP100 |
| 封装： | 14 X 20 MM, QIP-100 |
| 文件页数： | 7/31页 |
| 文件大小： | 381K |
| 代理商： | LV71081E |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页
LV71081E
No.A1610-15/31
Serial Control Specification
1. Slave address
2. DATA TRANSFER MANUAL : [1] is High level. [0] is Low level.
I
2C-BUS control system is adopted in SW LSI. SW LSI is controlled by SCL (Serial Clock) and SDA (Serial Data) At
first, please set up the START condition
*1 by these two terminals (SCL and SDA). And next, please input the 8bits data,
which should be synchronized with SCL into SDA terminal. Still more, please give priority to high rank bit at data
transfer order (MSB
→LSB). The 9th bit is called as ACK (Acknowledge), SW LSI sends [0] to the SDA terminal
during SCL [1] period. So, please open the port of microprocessor during this period. LV71081E adopt auto-increment,
so you input only first group-address and you can transfer data in order. As thus the Data transfer Stop condition
*2 is
finished.
*1 SDA rise up during SCI is [1]
*2 SDA fall down during SCL is [1]
3. TRANSFER DATA FORMAT
The transfer data is composed by START condition, Slave address, Group address
*1, data, and STOP condition.
After setting up the START condition, please transfer the Slave Address (regulated as “1001000” in SW LSI). Group
and next control data
*2 (Please see the Fig.1)
Slave Address is composed by 7bits, and this bit 8th bit
*3 should be set as [0].
The both of Group address and control data are composed by 8bits, and the one control action is defined with
combination of these two data. And if you want to control 2 or more groups at the same mode, you can realize it by
sending some control data together.
The data makes meaning with all bits, so you cannot stop the sending until all data transfer is over.
But LV71081E adopt auto-increment, for example you can stop to transfer STOP condition after group 2 data.
If you want to stop transfer action, please transfer the STOP condition without fail.
*1/2 There are 8 control groups.
*3 This 8th bit called as R/W bit, and this bit shows the data transmission direction. [0] means send mode (accept
mode with SW LSI) and [1] means accept mode (send mode with SW LSI) fundamentally. But SW LSI is not
equipped with such a data out function, please keep this bit as [0].
Fig. 1 DATA STRUCTURE
1
MSB
Slave receiver
One-way communication (this IC is dedicated to receive)
LSB
0010100
R/W ACK
ACK
.....
Stop condition
Start condition
Acknowledge
START condition
Slave address
Group address
Control data
STOP condition
相关PDF资料 |
PDF描述 |
|---|---|
| LV8018W | 0.5 A SWITCHING CONTROLLER, 130 kHz SWITCHING FREQ-MAX, PQFP48 |
| LV8095LQ | VOICE COIL MOTOR CONTROLLER, 0.2 A, PDSO8 |
| LV8095LQ | VOICE COIL MOTOR CONTROLLER, 0.2 A, PDSO8 |
| LV8099CS | VOICE COIL MOTOR CONTROLLER, 0.1 A, PBGA6 |
| LV8099CS | VOICE COIL MOTOR CONTROLLER, 0.1 A, PBGA6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LV71081E_11 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:For Video/Audio Signal Input/ Output Interface of DVD Recorder |
| LV71081E-MPB-E | 功能描述:显示驱动器和控制器 RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
| LV71081E-SPL-MPB-E | 制造商:ON Semiconductor 功能描述:VIDEO ICS - Trays 制造商:ON Semiconductor 功能描述:Video Switch ICs VIDEO ICS |
| LV7109E | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:AC Switch Europe SCART Standard |
| LV7109E-B-MPB-E | 功能描述:显示驱动器和控制器 RoHS:否 制造商:Panasonic Electronic Components 工作电源电压:2.7 V to 5.5 V 最大工作温度: 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Reel |
发布紧急采购，3分钟左右您将得到回复。