- 您现在的位置：买卖IC网 > PDF目录30777 > LV8011V (SANYO SEMICONDUCTOR CO LTD) BRUSH DC MOTOR CONTROLLER, 5 A, PDSO20 PDF资料下载
参数资料
| 型号： | LV8011V |
| 厂商： | SANYO SEMICONDUCTOR CO LTD |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSH DC MOTOR CONTROLLER, 5 A, PDSO20 |
| 封装： | 0.225 INCH, SSOP-20 |
| 文件页数： | 2/7页 |
| 文件大小： | 138K |
| 代理商： | LV8011V |
LV8011V
No.7230-2/7
Electric Characteristics at Ta = 25
°C, VCC = VM = 5.0V, SGND = PGND = 0V
Ratings
Parameter
Symbol
Conditions
min
typ
max
Unit
Remarks
Standby Power Source Current
for Load
IMO
EN = 0V
1.0
A
1
Standby Power Source Current
for Control
ICO
EN = 0V, IN1 = IN2 = TIN = 5V
50
100
A
2
Operating Current Consumption
IC1
EN = 5V, VG when non-load.
0.7
1.2
mA
3
High Level Input Voltage
VIH
2.5
VCC
V
Low Level Input Voltage
VIL
00.8
V
High Level Input Current
(IN1, IN2)
IIH
1.0
A
4
Low Level Input Current
(IN1, IN2)
IIL
-1.0
A
Pull-up Resistance Value
(EN, TIN)
RUP
50
100
200
k
Output ON Resistance
RON
Sum of top and bottom of ON
resistance value.
0.37
0.60
5
Charge-Pump Voltage
VG
9.5
10.4
11
V
6
Low Voltage Detection Operating
Voltage
VCS
VCC Voltage
2.3
2.5
2.7
V
7
Thermal Shutdown
Operating Temperature
TTSD
*Design Target
150
180
210
°C
8
Charge-Pump Capacity
(IG = 500
A)
VGLOAD
9.0
9.9
V
9
IG Current Dissipation
(Fin = 20kHz)
IG
350
A
10
Charge Pump Start-up Time
TVG
C1 = C2 = 0.01
F, CVG = 0.1F
0.5
1.0
ms
11
[Output Part]
Turn-ON Time
TPLH
0.9
2.0
s
12
Turn-OFF Time
TPHL
0.3
2.0
s
12
[TOUT]
Turn-ON Time
TOUT
C = 500pF
5.0
20
s
12
Turn-OFF Time
TOFF
C = 500pF
5.0
20
s
12
* It is a design target value and measurement is not carried out.
Remarks
1. It shows current dissipation of VM pin in output OFF state.
2. It shows current dissipation of VCC pin in stand-by state.
(The standard current depends on EN pin pull-down resistance.)
3. It shows current dissipation of VCC pin in state of EN = 5V (stand-by), including current dissipation of VG pin.
4. For IN1 and IN2 pins, no pull-down and pull-up resistance is needed. (High impedance pin)
5. It shows sum of upper and lower saturation voltages of OUT pin.
6. It controls charge-pump oscillation and makes specified voltage.
7. When low voltage is detected, the lower output is turned OFF.
8. When thermal protection circuit is activated, the lower output is turned OFF.
When the heat temperature is fallen, it is turned ON again.
9. IG (VG pin load current) = 500
F
10. It shows VG pin current dissipation in state of PWM input for IN pin.
11. It specifies start-up time from 10
% to 90% when VG is in non-load state
(when setting the capacitor between VG and GND to 0.1
F and VCC is 5V).
12. It specifies 10
% to 90% for start-up and 90% to 10% for shut-down.
相关PDF资料 |
PDF描述 |
|---|---|
| LV8042LG | STEPPER MOTOR CONTROLLER, 0.6 A, PBGA68 |
| LV8042LG | STEPPER MOTOR CONTROLLER, 0.6 A, PBGA68 |
| LV8054LP | STEPPER MOTOR CONTROLLER, 0.6 A, QCC40 |
| LV8054LP | STEPPER MOTOR CONTROLLER, 0.6 A, QCC40 |
| LV8414CS | STEPPER MOTOR CONTROLLER, 0.6 A, PBGA32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LV8011V_08 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Forward/Reverse Motor Driver |
| LV8011V-MPB-E | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LV8011V-TLM-E | 功能描述:马达/运动/点火控制器和驱动器 2.0-6.5V 1ch Brush Motor Driver RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LV8012T | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Forward/Reverse Motor Driver |
| LV8012T_09 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:Forward/Reverse Motor Driver |
发布紧急采购，3分钟左右您将得到回复。