- 您现在的位置：买卖IC网 > PDF目录69008 > LV8731V (SANYO SEMICONDUCTOR CO LTD) STEPPER MOTOR CONTROLLER, 2.5 A, PDSO44 PDF资料下载
参数资料
| 型号： | LV8731V |
| 厂商： | SANYO SEMICONDUCTOR CO LTD |
| 元件分类： | 运动控制电子 |
| 英文描述： | STEPPER MOTOR CONTROLLER, 2.5 A, PDSO44 |
| 封装： | 0.275 INCH, SSOP-44 |
| 文件页数： | 3/26页 |
| 文件大小： | 323K |
| 代理商： | LV8731V |
LV8731V
No.A1482-11/26
(4) Setting constant-current control reference current
This IC is designed to automatically exercise PWM constant-current chopping control for the motor current by setting
the output current. Based on the voltage input to the VREF pin and the resistance connected between RF and GND,
the output current that is subject to the constant-current control is set using the calculation formula below :
IOUT = (VREF/5)/RF resistance
* The above setting is the output current at 100% of each excitation mode.
The voltage input to the VREF pin can be switched to four-step settings depending on the statuses of the two inputs,
ATT1 and ATT2. This is effective for reducing power consumption when motor holding current is supplied.
Attenuation function for VREF input voltage
ATT1
ATT2
Current setting reference voltage attenuation ratio
Low
100%
High
Low
80%
Low
High
50%
High
20%
The formula used to calculate the output current when using the function for attenuating the VREF input voltage is
given below.
IOUT = (VREF/5) × (attenuation ratio)/RF resistance
Example : At VREF of 1.5V, a reference voltage setting of 100% [(ATT1, ATT2) = (L, L)] and an RF resistance of
0.3
Ω, the output current is set as shown below.
IOUT = 1.5V/5 × 100%/0.3Ω = 1.0A
If, in this state, (ATT1, ATT2) is set to (H, H), IOUT will be as follows :
IOUT = 1.0A × 20% = 200mA
In this way, the output current is attenuated when the motor holding current is supplied so that power can
be conserved.
(5) Blanking period
If, when exercising PWM constant-current chopping control over the motor current, the mode is switched from decay
to charge, the recovery current of the parasitic diode may flow to the current sensing resistance, causing noise to be
carried on the current sensing resistance pin, and this may result in erroneous detection. To prevent this erroneous
detection, a blanking period is provided to prevent the noise occurring during mode switching from being received.
During this period, the mode is not switched from charge to decay even if noise is carried on the current sensing
resistance pin.
In the stepping motor driver mode (DM = Low or Open) of this IC, the blanking time is fixed at approximately 1
μs.
In the DC motor driver mode (DM = High), the blanking time can be switched to one of two levels using the
RST/BLK pin. (Refer to "Blanking time switching function.")
相关PDF资料 |
PDF描述 |
|---|---|
| LV8772 | STEPPER MOTOR CONTROLLER, DIP28 |
| LX1675ILQ-TR | 1.5 A SWITCHING CONTROLLER, 690 kHz SWITCHING FREQ-MAX, PQCC38 |
| LX1675CLQ-TR | 1.5 A SWITCHING CONTROLLER, 690 kHz SWITCHING FREQ-MAX, PQCC38 |
| LX1684CDT | 1 A SWITCHING CONTROLLER, 200 kHz SWITCHING FREQ-MAX, PDSO14 |
| LX1689CPW-TR | FLUORESCENT LIGHT CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO20 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LV8731VGEVB | 功能描述:电源管理IC开发工具 EVM FOR LV8731V RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| LV8731V-MPB-H | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LV8731V-TLM-H | 功能描述:马达/运动/点火控制器和驱动器 9-32VSteppingMotor 2chBrush Motor Dr RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LV8732V | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:PWM Constant-Current Control Stepping Motor Driver |
| LV8732V_10 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:PWM Constant-Current Control Stepping Motor Driver |
发布紧急采购，3分钟左右您将得到回复。