- 您现在的位置：买卖IC网 > PDF目录79982 > LV8747T (SANYO SEMICONDUCTOR CO LTD) 1.75 A SWITCHING CONTROLLER, 150 kHz SWITCHING FREQ-MAX, PQFP64 PDF资料下载
参数资料
| 型号： | LV8747T |
| 厂商： | SANYO SEMICONDUCTOR CO LTD |
| 元件分类： | 稳压器 |
| 英文描述： | 1.75 A SWITCHING CONTROLLER, 150 kHz SWITCHING FREQ-MAX, PQFP64 |
| 封装： | 7 X 7 MM, TQFP-64 |
| 文件页数： | 10/21页 |
| 文件大小： | 228K |
| 代理商： | LV8747T |
LV8747T
No.A0695-18/21
Output short-circuit protection circuit
To protect IC from damage due to short-circuit of the output caused by lightening or ground fault, the output short-circuit
protection circuit to put the output in the standby mode is incorporated.
(1) Output short-circuit protection operation changeover function
Changeover to the output short-circuit protection of IC is made by the setting of OCPM pin.
OCPM
State
“Low”
Auto reset method
“High”
Latch method
(Auto reset method)
When the output current is below the output short-circuit protection current, the output is controlled by the input signal.
When the output current exceeds the detection current, the switching waveform as shown below appears instead.
When detecting the output short-circuit state, the short-circuit detection circuit is activated.
When the short-circuit detection circuit operation exceeds the timer latch time described later, the output is changed
over to the standby mode and reset to the ON mode again in 256s (TYP). In this event, if the over-current mode still
continues, the above switching mode is repeated till the over-current mode is canceled.
(Latch method)
Similarly to the case of automatic reset method, the short-circuit detection circuit is activated when it detects the
output short-circuit state.
When the short-circuit detection circuit operation exceeds the timer latch time described later, the output is changed
over to the standby mode.
In this method, latch is released by setting PS = “L”
(2) OCP pin constant setting method (timer latch setting)
Connect C between the OCP pin and GND, and the time up to the output OFF can be set in case of output short-circuit.
The C value can be determined as follows :
Timer latch : Tocp
Tocp
≈ C × V/I [s]
V : Threshold voltage TYP 1V
I : OCP charge current TYP 20
A
(C: Recommended constant value 100pF to 200pF)
ON
1V
OCP voltage
Output current
Exceeding the
over-current
detection
current
OFF
0.5 to 1
s
256
s (TYP)
OFF
ON
相关PDF资料 |
PDF描述 |
|---|---|
| LSN-5/10-D12B | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| LTC3410ESC6-1.2 | 0.63 A SWITCHING REGULATOR, 2700 kHz SWITCHING FREQ-MAX, PDSO6 |
| LT3579EFE-1#PBF | SWITCHING REGULATOR, PDSO20 |
| LTC3521IFE#TRPBF | SWITCHING REGULATOR, 1350 kHz SWITCHING FREQ-MAX, PDSO20 |
| LS4501-9PD6TB1 | 1-OUTPUT 100 W AC-DC PWR FACTOR CORR MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LV8747TA | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:PWM Constant-Current Control Stepping Motor Driver and Switching Regulator Controller |
| LV8747TA-2H | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LV8747TA-AE | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LV8747TA-NH | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LV8747T-TLM-E | 功能描述:马达/运动/点火控制器和驱动器 10-35V Step w SW-Reg 2chBrush Motor Dr RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。