- 您现在的位置：买卖IC网 > PDF目录65797 > LV8804FV (SANYO SEMICONDUCTOR CO LTD) AC MOTOR CONTROLLER, 1.2 A, PDSO20 PDF资料下载
参数资料
| 型号： | LV8804FV |
| 厂商： | SANYO SEMICONDUCTOR CO LTD |
| 元件分类： | 运动控制电子 |
| 英文描述： | AC MOTOR CONTROLLER, 1.2 A, PDSO20 |
| 封装： | 0.225 INCH, SSOP-20 |
| 文件页数： | 9/9页 |
| 文件大小： | 111K |
| 代理商： | LV8804FV |
LV8804FV
PS No.A1441-9/9
SANYO Semiconductor Co.,Ltd. assumes no responsibility for equipment failures that result from using
products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition
ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor Co.,Ltd.
products described or contained herein.
SANYO Semiconductor Co.,Ltd. strives to supply high-quality high-reliability products, however, any and all
semiconductor products fail or malfunction with some probability. It is possible that these probabilistic failures or
malfunction could give rise to accidents or events that could endanger human lives, trouble that could give rise
to smoke or fire, or accidents that could cause damage to other property. When designing equipment, adopt
safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not
limited to protective circuits and error prevention circuits for safe design, redundant design, and structural
design.
Upon using the technical information or products described herein, neither warranty nor license shall be granted
with regard to intellectual property rights or any other rights of SANYO Semiconductor Co.,Ltd. or any third
party. SANYO Semiconductor Co.,Ltd. shall not be liable for any claim or suits with regard to a third party's
intellctual property rights which has resulted from the use of the technical information and products mentioned
above.
Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed
for volume production.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the
SANYO Semiconductor Co.,Ltd. product that you intend to use.
In the event that any or all SANYO Semiconductor Co.,Ltd. products described or contained herein are
controlled under any of applicable local export control laws and regulations, such products may require the
export license from the authorities concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise,
without the prior written consent of SANYO Semiconductor Co.,Ltd.
*7. OSC pin
This pin is used to connect the capacitor for setting the startup frequency.
A capacitor with a capacitance ranging from about 500pF to 2,200pF (recommended value) must be connected
between this pin and GND.
The OSC pin determines the motor startup frequency, so be sure to connect a capacitor to it.
<How to select the capacitance>
Select a capacitance value that will result in the shortest possible startup time for achieving the target speed and
produce minimal variations in the startup time. If the capacitance is too high, variations in the startup time will
increase; conversely, if it is too low, the motor may idle. The optimum OSC constant depends on the motor
characteristics and startup current, so be sure to recheck them when the type of motor used or circuit specifications are
changed.
*8. MINSP pin
This pin is used to input the voltage to set the minimum speed.
The minimum speed can be set by resistor-dividing the VREG voltage (5V) to create a voltage of 1 to 3V, and
inputting this voltage to the MINSP pin.
If the minimum speed is not going to be set, the MINSP pin and CTL pin must be short-circuited.
*9. VG, CP, and CPC pins
These pins are used to connect the capacitors to generate the pre-drive voltage and stabilize the pre-drive power
supply.
Be sure to connect these capacitors in order to generate the drive voltage for the high-side (upper) output DMOS
transistor.
*10. VREG pins
These are the control system power supply pin and regulator output pin, which create the power supply of the control
unit. Be sure to connect a capacitor between this pin and GND in order to stabilize control system operation.
Since these pins are used to supply current for control and generate the charge pump voltage, connect a capacitor with
a capacitance that is higher than that of the capacitor connected to the charge pump.
This catalog provides information as of April, 2009. Specifications and information herein are subject
to change without notice.
相关PDF资料 |
PDF描述 |
|---|---|
| LV8804V | BRUSH DC MOTOR CONTROLLER, 1.2 A, PDSO36 |
| LV8804V | BRUSH DC MOTOR CONTROLLER, 1.2 A, PDSO36 |
| LV8805SV | AC MOTOR CONTROLLER, 1.2 A, PDSO20 |
| LV8805SV | AC MOTOR CONTROLLER, 1.2 A, PDSO20 |
| LX1670CD-TR | 1-OUTPUT THREE TERM VOLTAGE REFERENCE, PDSO14 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LV8804FV_11 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:PC and Server Fan Motor Driver |
| LV8804FV_12 | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:PC and Server Fan Motor Driver |
| LV8804FV-D | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:PC and Server Fan Motor Driver |
| LV8804FVGEVB | 功能描述:电源管理IC开发工具 EVABORD FOR LV8804FV RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| LV8804FV-MPB-H | 功能描述:马达/运动/点火控制器和驱动器 FAN MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。