- 您现在的位置：买卖IC网 > PDF目录53673 > LV8805V AC MOTOR CONTROLLER, PDSO36 PDF资料下载
参数资料
| 型号： | LV8805V |
| 元件分类： | 运动控制电子 |
| 英文描述： | AC MOTOR CONTROLLER, PDSO36 |
| 封装： | SSOP-36 |
| 文件页数： | 8/9页 |
| 文件大小： | 191K |
| 代理商： | LV8805V |
LV8805V
No.A1747-8/9
*5. RF pins
These pins are used to set the current limit.
When the pin voltage exceeds 0.25V, the current is limited, and regeneration mode is established. In the application
circuit, this voltage is set in such a way that the current limit will be established at 1A.
The calculation formula is given below.
RF resistance = 0.25V/target current limit value
All the RF pins (pins 24, 26 and 27) must be short-circuited on the print pattern.
*6. SOFTST pin
This pin is used to set the soft start.
By connecting a capacitor between this pin and GND, the motor speed can be increased gradually.
When the pin voltage exceeds 2.5V, the soft start is released, and the LV8804V is switched to normal control.
If the soft start function is not going to be used, connect the pin to the VREG pin.
*7. OSC pin
This pin is used to connect the capacitor for setting the startup frequency.
A capacitor with a capacitance ranging from about 500pF to 2,200pF (reference value) must be connected between
this pin and GND.
The OSC pin determines the motor startup frequency, so be sure to connect a capacitor to it.
<How to select the capacitance>
Select a capacitance value that will result in the shortest possible startup time for achieving the target speed and
produce minimal variations in the startup time. If the capacitance is too high, variations in the startup time will
increase; conversely, if it is too low, the motor may idle. The optimum OSC constant depends on the motor
characteristics and startup current, so be sure to recheck them when the type of motor used or circuit specifications are
changed.
*8. VG, CP, and CPC pins
These pins are used to connect the capacitors to generate the pre-drive voltage and stabilize the pre-drive power
supply.
Be sure to connect these capacitors in order to generate the drive voltage for the high-side (upper) output DMOS
transistor.
*9. VREG pins
These are the control system power supply pin and regulator output pin, which create the power supply of the control
unit. Be sure to connect a capacitor between this pin and GND in order to stabilize control system operation.
Since these pins are used to supply current for control and generate the charge pump voltage, connect a capacitor with
a capacitance that is higher than that of the capacitor connected to the charge pump.
Both the VREG pins (pins 3 and 4) must be short-circuited on the print pattern.
相关PDF资料 |
PDF描述 |
|---|---|
| LV8806GQ | AC MOTOR CONTROLLER, QCC16 |
| LWM12S05/3000XA | 1-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| LX1004CLP-1.2-TR | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.235 V, PBCY3 |
| LX1004CLP-1.2 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.235 V, PBCY3 |
| LX1004CDM-1.2 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 1.235 V, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LV8805V-MPB-H | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LV8805V-TLM-H | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LV8806GQ | 制造商:SANYO 制造商全称:Sanyo Semicon Device 功能描述:3-phase sensor-less Motor Driver IC |
| LV8806GQ-TE-L-H | 功能描述:马达/运动/点火控制器和驱动器 FAN MOTOR DRIVER RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LV8806QA-MH | 制造商:ON Semiconductor 功能描述:3PHASE MOTOR DRIVER - Tape and Reel 制造商:ON Semiconductor 功能描述:REEL / 3PHASE MOTOR DRIVER |
发布紧急采购，3分钟左右您将得到回复。