- 您现在的位置：买卖IC网 > PDF目录45001 > LV8829LF (SANYO SEMICONDUCTOR CO LTD) BRUSHLESS DC MOTOR CONTROLLER, 1.5 A, QCC24 PDF资料下载
参数资料
| 型号： | LV8829LF |
| 厂商： | SANYO SEMICONDUCTOR CO LTD |
| 元件分类： | 运动控制电子 |
| 英文描述： | BRUSHLESS DC MOTOR CONTROLLER, 1.5 A, QCC24 |
| 封装： | 4 X 4 MM, VQFN-24 |
| 文件页数： | 3/13页 |
| 文件大小： | 263K |
| 代理商： | LV8829LF |
LV8829LF
5. Hall Input Signal
A pulse input with the amplitude in excess of the hysteresis (35mV maximum) is required for the Hall inputs.
It is desirable that the amplitude of the Hall input signal be 100mVp-p or more in consideration of the effect of noise
and phase displacement.
If disturbances to the output waveform (during phase switching) occur due to noise, connect a capacitor between the
Hall input pins to prevent such disturbances. In the constraint protection circuit, the Hall input is utilized as a judgment
signal. Although the circuit ignores a certain amount of noise, caution is necessary.
If all three phases of the Hall input signal go to the same input state (HHH or LLL), the outputs are all set to the OFF
state.
If the Hall IC is used, fixing one side of the inputs (either the + or – side) at a voltage within the common-mode input
voltage range (between 0.3V and VREG-1.7V) allows the other input side to be used as an input over the 0V to VREG
range.
○ Method of connecting Hall elements
Type (1) connection (three Hall elements connected in series)
Advantages
Because the current flowing in Hall elements can be shared by connecting the Hall elements in series, the current
consumption is less than that of a parallel-connected arrangement.
The use of a current limiting resistor can be eliminated.
Fluctuations of amplitude with temperature are reduced.
Disadvantages
Because only 1V can be applied to one Hall device, there is a possibility that adequate amplitude cannot be
obtained.
The current flowing in the Hall elements varies with temperature.
Type (2) connection (three Hall elements connected in parallel)
Advantages
The current flowing in the Hall elements can be determined by the current limiting resistor.
The voltage applied to the Hall elements can be varied, enabling adequate amplitude to be obtained.
Disadvantages
Because it is necessary to supply current separately to each Hall element, the current consumption becomes large.
A current limiting resistor is necessary.
The amplitude varies with temperature.
VCC
HB
3V Constant-voltage Output
VCC
HB
3V Constant-voltage Output
(1)
(2)
○ HB pin
The HB pin is used for cutting off the current flowing in the Hall elements during standby (for saving electricity).
The output from the HB pin is set to OFF in the following cases.
When the S/S pin is in a STOP state
When 0% duty is detected at the PWMIN pin input
No.A1801-11/13
相关PDF资料 |
PDF描述 |
|---|---|
| LW005A | DC-DC REG PWR SUPPLY MODULE |
| LW005B | DC-DC REG PWR SUPPLY MODULE |
| LC005B | DC-DC REG PWR SUPPLY MODULE |
| LC005F | DC-DC REG PWR SUPPLY MODULE |
| LW010F | 1-OUTPUT 8 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LV8829LFQA | 制造商:ONSEMI 制造商全称:ON Semiconductor 功能描述:For Brushless Motor Drive PWM Driver IC |
| LV8829LFQAGEVK | 制造商:ON Semiconductor 功能描述:DEMO BD FOR LV8829LFQA - Bulk 制造商:ON Semiconductor 功能描述:KIT EVAL FOR LV8829LFQA |
| LV8829LFQA-NH | 功能描述:马达/运动/点火控制器和驱动器 RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| LV8829LF-TLM-H | 功能描述:IC MOTOR DRIVER 24-VQFN 4X4 RoHS:是 类别:集成电路 (IC) >> PMIC - MOSFET，电桥驱动器 - 外部开关 系列:* 标准包装:50 系列:- 配置:高端 输入类型:非反相 延迟时间:200ns 电流 - 峰:250mA 配置数:1 输出数:1 高端电压 - 最大（自引导启动）:600V 电源电压:12 V ~ 20 V 工作温度:-40°C ~ 125°C 安装类型:通孔 封装/外壳:8-DIP（0.300"，7.62mm） 供应商设备封装:8-DIP 包装:管件 其它名称:*IR2127 |
| LV8844DEV-106.25M | 功能描述:标准时钟振荡器 106.25MHz 3.3V 25ppm -40+85DC RoHS:否 制造商:AVX 产品:Standard Clock Oscillators 封装 / 箱体:7 mm x 5 mm 频率:75 MHz 频率稳定性:50 PPM 电源电压:2.5 V 负载电容: 端接类型:SMD/SMT 最小工作温度:0 C 最大工作温度:+ 70 C 输出格式:LVDS 尺寸: 封装:Reel 系列: |
发布紧急采购，3分钟左右您将得到回复。