参数资料
型号: LW016CL1
厂商: LINEAGE POWER LLC
元件分类: 电源模块
英文描述: 2-OUTPUT 16 W DC-DC REG PWR SUPPLY MODULE
封装: MODULE-9
文件页数: 2/16页
文件大小: 486K
代理商: LW016CL1
10
LW016 Dual-Output-Series Power Modules:
Advance Data Sheet
36 Vdc to 75 Vdc Inputs; 16 W
April 2008
Lineage Power
Feature Descriptions (continued)
Output Voltage Adjustment (continued)
The combination of the output voltage adjustment and
sense range and the output voltage given in the Fea-
ture Specifications table cannot exceed 110% of the
nominal output voltage between the VO(+) and VO(–)
terminals.
The modules have fixed current-limit set points. There-
fore, as the output voltage is adjusted down, the avail-
able output power is reduced. In addition, the minimum
output current is a function of the output voltage. As the
output voltage is adjusted down, the minimum required
output current can increase.
Output Overvoltage Protection
The output overvoltage clamp consists of control cir-
cuitry, independent of the primary regulation loop, that
monitors the voltage on the output terminals. The con-
trol loop of the protection circuit has a higher voltage
set point than the primary loop (see Feature Specifica-
tions table). In a fault condition, the overvoltage clamp
ensures that the output voltage does not exceed VO,
clamp, max
. This provides a redundant voltage-control that
reduces the risk of output overvoltage.
Synchronization (Optional)
The unit is capable of external synchronization from an
independent time base with a switching rate of
256 kHz. The amplitude of the synchronizing pulse
train is TTL compatible and the duty cycle ranges
between 40% and 60%. Synchronization is referenced
to VI(+).
Thermal Considerations
Introduction
The LW016 Dual-Output-Series power module oper-
ates in a variety of thermal environments; however,
sufficient cooling should be provided to help ensure
reliable operation of the unit. Heat-dissipating compo-
nents inside the unit are thermally coupled to the case.
Heat is removed by conduction, convection, and radia-
tion to the surrounding environment. Proper cooling
can be verified by measuring the case temperature.
Peak case temperature (TC) occurs at the position indi-
cated in Figure 11.
8-1265(C).d
Note: Dimensions are in millimeters and (inches).
Figure 11. Case Temperature Measurement
Location
Note that the view in Figure 11 is of the metal surface of
the module—the pin locations shown are for reference.
The temperature at this location should not exceed the
maximum case temperature (100 °C). The output
power of the module should not exceed the rated
power for the module as listed in the Ordering Informa-
tion table.
Heat Transfer
Increasing airflow over the module enhances the heat
transfer via convection. Figure 12 shows the maximum
power that can be dissipated by the module without
exceeding the maximum case temperature versus local
ambient temperature (TA) for natural convection
through 2.0 ms–1 (400 ft./min.).
Note that the natural convection condition was mea-
sured at 0.05 ms–1 (10 ft./min.) to 0.1 ms–1 (20 ft./min.);
however, systems in which these power modules may
be used typically generate natural convection airflow
rates of 0.3 ms–1 (60 ft./min.) due to other heat-dissi-
pating components in the system. Use of Figure 12 is
shown in the following example.
相关PDF资料
PDF描述
LW016CL8 2-OUTPUT 16 W DC-DC REG PWR SUPPLY MODULE
LB11868V DISK DRIVE MOTOR CONTROLLER, PDSO20
LT1460DCS8-10#TRPBF1460 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 10 V, PDSO8
LT1460FCMS8-5#TR1460 1-OUTPUT THREE TERM VOLTAGE REFERENCE, 5 V, PDSO8
LS75-3 1-OUTPUT DC-DC UNREG PWR SUPPLY MODULE
相关代理商/技术参数
参数描述
LW016CL3 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC
LW016CL7 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC
LW016CL8 制造商:未知厂家 制造商全称:未知厂家 功能描述:Analog IC
LW016FA87 制造商:TE Connectivity 功能描述:
LW020 制造商:VISHAY 制造商全称:Vishay Siliconix 功能描述:LW020 Single-Output-Series Power Modules 36 Vdc to 75 Vdc inputs 20W