- 您现在的位置：买卖IC网 > PDF目录80307 > LW025A (LINEAGE POWER LLC) 1-OUTPUT 25 W DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | LW025A |
| 厂商： | LINEAGE POWER LLC |
| 元件分类： | 电源模块 |
| 英文描述： | 1-OUTPUT 25 W DC-DC REG PWR SUPPLY MODULE |
| 封装： | MODULE-8 |
| 文件页数： | 15/16页 |
| 文件大小： | 417K |
| 代理商： | LW025A |
88
Lineage Power
Advance Data Sheet
April 2008
36 Vdc to 75 Vdc Inputs; 25 W
LW025 Single-Output-Series Power Modules:
Design Considerations
Grounding Considerations
For modules without the isolated case ground pin
option, the case is internally connected to the VI(+) pin.
For modules with the isolated case ground pin, device
code suffix “7,” the VI(+) pin is not connected to the
case.
Input Source Impedance
The power module should be connected to a low ac-
impedance input source. Highly inductive source
impedances can affect the stability of the power mod-
ule. For the test configuration in Figure 10, a 33 F
electrolytic capacitor (ESR < 0.7 at 100 kHz)
mounted close to the power module helps ensure sta-
bility of the unit. For other highly inductive source
impedances, consult the factory for further application
guidelines.
Safety Considerations
For safety-agency approval of the system in which the
power module is used, the power module must be
installed in compliance with the spacing and separation
requirements of the end-use safety agency standard,
i.e., UL 1950, CSA C22.2 No. 950-95, and VDE 0805
(EN60950, IEC950).
If the input source is non-SELV (ELV or a hazardous
voltage greater than 60 Vdc and less than or equal to
75 Vdc), for the module's output to be considered
meeting the requirements of safety extra-low voltage
(SELV), all of the following must be true:
n
The input source is to be provided with reinforced
insulation from any other hazardous voltages, includ-
ing the ac mains; and
n
One VI pin and one VO pin are to be grounded or
both the input and output pins are to be kept floating;
and
n
The input pins of the module are not operator acces-
sible; and
n
Another SELV reliability test is conducted on the
whole system, as required by the safety agencies, on
the combination of supply source and the subject
module to verify that under a single fault, hazardous
voltages do not appear at the module's output.
Note: Do not ground either of the input pins of the
module without grounding one of the output
pins. This may allow a non-SELV voltage to
appear between the output pins and ground.
The power module has extra-low voltage (ELV) outputs
when all inputs are ELV.
The input to these units is to be provided with a maxi-
mum 5 A normal-blow fuse in the ungrounded lead.
Feature Descriptions
Overcurrent Protection
To provide protection in a fault (output overload) condi-
tion, the unit is equipped with internal current-limiting
circuitry and can endure current limiting for an unlim-
ited duration. At the point of current-limit inception, the
unit shifts from voltage control to current control. If the
output voltage is pulled very low during a severe fault,
the current-limit circuit can exhibit either foldback or
tailout characteristics (output-current decrease or
increase). The unit operates normally once the output
current is brought back into its specified range.
Remote On/Off
Two remote on/off options are available. Positive logic
remote on/off turns the module on during a logic-high
voltage on the REMOTE ON/OFF pin, and off during a
logic low. Negative logic, device code suffix “1,” remote
on/off turns the module off during a logic high and on
during a logic low.
To turn the power module on and off, the user must
supply a switch to control the voltage between the
on/off terminal and the VI(–) terminal (Von/off). The
switch can be an open collector or equivalent (see Fig-
imum Ion/off during a logic low is 1 mA. The switch
should maintain a logic-low voltage while sinking 1 mA.
During a logic high, the maximum Von/off generated by
the power module is 6 V. The maximum allowable leak-
age current of the switch at Von/off = 6 V is 50 A.
The module has internal capacitance to reduce noise
at the ON/OFF pin. Additional capacitance is not gen-
erally needed and may degrade the start-up character-
istics of the module.
相关PDF资料 |
PDF描述 |
|---|---|
| LTC3109IUF#PBF | 0.026 A SWITCHING REGULATOR, PQCC20 |
| LDO10C-015W05-HJ | 1-OUTPUT 50 W DC-DC REG PWR SUPPLY MODULE |
| LM4040ETB-330GT3 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 3.3 V, PDSO3 |
| LWN2880-6ERD2M2FK2G | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| LTC4000IGN#TRPBF | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, PDSO28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LW025A1 | 功能描述:CONVERTER DC/DC 5V 25W OUT RoHS:否 类别:电源 - 板载 >> DC DC Converters 系列:LW025 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:42V 电压 - 输入（最大）:60V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:150W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9-SlimMod 尺寸/尺寸:4.60" L x 1.80" W x 0.52" H（116.8mm x 45.7mm x 13.2mm） 包装:散装 工作温度:-55°C ~ 85°C 效率:* 电源（瓦特）- 最大:* |
| LW025F | 制造商:MA-COM 制造商全称:M/A-COM Technology Solutions, Inc. 功能描述:LW025 Single-Output-Series Power Modules 36 Vdc to 75 Vdc Inputs 25 W |
| LW025F8 | 功能描述:CONVERTER DC/DC 3.3V 16.5W OUT RoHS:否 类别:电源 - 板载 >> DC DC Converters 系列:LW025 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:42V 电压 - 输入（最大）:60V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:150W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9-SlimMod 尺寸/尺寸:4.60" L x 1.80" W x 0.52" H（116.8mm x 45.7mm x 13.2mm） 包装:散装 工作温度:-55°C ~ 85°C 效率:* 电源（瓦特）- 最大:* |
| LW025F871 | 功能描述:CONVERTER DC/DC 3.3V 16.5W OUT RoHS:否 类别:电源 - 板载 >> DC DC Converters 系列:LW025 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:42V 电压 - 输入（最大）:60V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:150W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9-SlimMod 尺寸/尺寸:4.60" L x 1.80" W x 0.52" H（116.8mm x 45.7mm x 13.2mm） 包装:散装 工作温度:-55°C ~ 85°C 效率:* 电源（瓦特）- 最大:* |
| LW025G | 功能描述:CONVERTER DC/DC 2.5V 12.5W OUT RoHS:否 类别:电源 - 板载 >> DC DC Converters 系列:LW025 设计资源:VI-200, VI-J00 Design Guide, Appl Manual 标准包装:1 系列:* 类型:隔离 输出数:1 电压 - 输入（最小）:42V 电压 - 输入（最大）:60V Voltage - Output 1:15V Voltage - Output 2:- Voltage - Output 3:- 电流 - 输出（最大）:* 电源（瓦） - 制造商系列:150W 电压 - 隔离:* 特点:* 安装类型:通孔 封装/外壳:9-SlimMod 尺寸/尺寸:4.60" L x 1.80" W x 0.52" H（116.8mm x 45.7mm x 13.2mm） 包装:散装 工作温度:-55°C ~ 85°C 效率:* 电源（瓦特）- 最大:* |
发布紧急采购，3分钟左右您将得到回复。