- 您现在的位置：买卖IC网 > PDF目录240282 > LWR1301-6ERFK2G (POWER-ONE INC) DC-DC REG PWR SUPPLY MODULE PDF资料下载
参数资料
| 型号： | LWR1301-6ERFK2G |
| 厂商： | POWER-ONE INC |
| 元件分类： | 电源模块 |
| 英文描述： | DC-DC REG PWR SUPPLY MODULE |
| 封装： | ROHS COMPLIANT |
| 文件页数： | 16/28页 |
| 文件大小： | 1316K |
| 代理商： | LWR1301-6ERFK2G |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页
BCD20020-G REV AA
Page 23 of 28
www.power-one.com
W Series Data Sheet
125, 250 Watt AC-DC and DC-DC DIN-Rail Converters
Fig. 24
System connectors Option K2
R: Adjustment of Vo or Vo2
The R input allows external adjustment of the output voltage in
the range of 50% to 110% Vo nom. Double-output models allow
only adjustment of output 2 (connected to the terminals 6, 7, 8
and 9). This enables asymmetric output voltage configuration.
Adjustment can be achieved via a resistor or an external
voltage source (in the range of 1.25 – 2.75 V).
Note: If the R input is not connected: Vo or Vo2
≈ Vo nom.
a) Adjustment by an external resistor:
Resistor Rext1, connected between R (pin 2) and GND1 (pin
1) of the D-SUB connector or according to fig. 20.
Vo
Vo = 50 – 100% Vo nom. Rext1
≈ 4 k –––––––––
Vo nom – Vo
Resistor Rext2, connected between R (pin 2) and VCC (pin 3)
of the D-SUB connector or according to fig. 20.
Vo – 2.5 V
Vo = 100 – 110% Vo nom. Rext2
≈ 4k ––––––––––––––––
2.5 V(Vo / Vo nom –1)
Note: If the R function is not included in M1 or M2, refer to figure
20 how to connect
Rext1 or Rext2 .
b) Adjustment by an external control voltage Vext (1.25 – 2.75
V), connected between R (pin 2) and GND (pin 1) of the D-
SUB connector or according to fig. 20.
Vo
Vext
Vext
≈ 2.5 V –––––
Vo
≈ Vo nom ––––
Vo nom
2.5 V
Caution: To prevent damage, Vext should not exceed 3 V, nor be
negative.
Note: If longer wires are used to connect the R input at the D-SUB
connector, the wiring to pin 1 (GND1) should be done as star point
connection. If wired differently, the output voltage setting may be
adversely affected.
In battery charging systems, an external battery temperature
sensor (see Accessories) can be connected to optimize Vo.
However, adjustment using the R input (pin 2 of D-SUB) is
possible as well. The above shown formulas are valid, but
Vo nom stands for the voltage with open R input (= Vo safe).
Option F: Built-in Second Fuse
A built-in second fuse in the neutral line provides safe phase-
to-phase connection at low mains voltages (e.g., USA 120 V/
208 V /60 Hz systems).
The built-in second fuse also enables safe connection to the
mains, where phase and neutral are not defined or cannot be
identified, as e.g., in the case of plug and socket connection to
the mains via German Schuko-plugs; see also Safety and
Installation Instructions.
Option F limits the DC input voltage to
≤ 250 V.
Option Q: Reverse Polarity Protection
EW models have no bridge rectifier at the input. To provide
reverse polarity protection, an additional diode can be fitted.
However this lowers the efficiency by approximately 1%.
Option K2: System Connectors
For installation in systems using pre-assembled harnesses the
converters are available with system connectors. They are UL-
listed, approved for currents up to 15 A at –40 to 105 °C.
The mating system connectors with screw terminals and
retainers are delivered together with every converter with
option K2. Use max. 2.5 mm2 (AWG 12) solid or stranded
wires, or max. 1.5 mm2 (AWG 14) stranded wires with crimp
termination, stripped length 6 mm. Tightening torque of input/
output terminals: max. 0.79 Nm (7 lbs.in.).
Option G
RoHS compliant for all six substances.
Table 19: System OK (M1 with external battery sensor)
System Status
Input
Vcontrol
Vbat
D5
sensor signal
theoretical
measured
output
System OK
O.K.
2.7 V
27 V
Low ohmic
Battery overchared / temp. sensor
O.K.
2.7 V
27 V
28 V
High ohmic
defect / control voltage to high
Overload, converter cannot follow the
O.K.
2.7 V
27 V
24 V
High ohmic
control signal
Output does not follow control signal,
O.K.
3.0 V
30 V
27 V
High ohmic
since battery would be overcharged
System OK
O.K.
2.5 V
25 V
25V
Low ohmic
相关PDF资料 |
PDF描述 |
|---|---|
| LT3574IMS#PBF | 1.1 A SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| LSP5503SEAC | 4 A SWITCHING REGULATOR, 470 kHz SWITCHING FREQ-MAX, PDSO8 |
| LMX2332TM | PLL FREQUENCY SYNTHESIZER, 1200 MHz, PDSO20 |
| LM4040AIMX-8.2 | 1-OUTPUT TWO TERM VOLTAGE REFERENCE, 8.192 V, PDSO8 |
| LFD9DP | 2-OUTPUT 65 W DC-DC REG PWR SUPPLY MODULE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LWR-1601-6 | 制造商:POWER-ONE 制造商全称:Power-One 功能描述:125 and 250 Watt AC-DC Converters |
| LWR1601-6 | 制造商:Power-One 功能描述:AC/DC PS SGL-OUT 24.7V 5A 125W 5PIN - Bulk |
| LWR16016-6E | 制造商:Power-One 功能描述: |
| LWR1601-6E | 功能描述:DC/DC转换器 DIN Rail 124W (24.7V) RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| LWR1601-6EG | 功能描述:DC/DC转换器 125W W-DIN-Rail Converters SNGL OUT RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
发布紧急采购，3分钟左右您将得到回复。