- 您现在的位置：买卖IC网 > PDF目录45007 > LX1563IDM-TR (MICROSEMI CORP-ANALOG MIXED SIGNAL GROUP) 0.5 A POWER FACTOR CONTROLLER, PDSO8 PDF资料下载
参数资料
| 型号： | LX1563IDM-TR |
| 厂商： | MICROSEMI CORP-ANALOG MIXED SIGNAL GROUP |
| 元件分类： | 稳压器 |
| 英文描述： | 0.5 A POWER FACTOR CONTROLLER, PDSO8 |
| 封装： | ROHS COMPLIANT, PLASTIC, SOIC-8 |
| 文件页数： | 6/25页 |
| 文件大小： | 430K |
| 代理商： | LX1563IDM-TR |
SECOND-GENERATION POWER FACTOR C ONTROLLER
LX1562/1563
PRODUCT DA T ABOOK 1996/1997
Copyright 1996
Rev. 1.3a
8/30
14
P RODUCTION D ATA
S HEET
IC DESCRIPTION
ERROR AMPLIFIER
The error amplifier is an internally compensated op-amp with
access to the inverting input and the output pin.
The non-
inverting input is internally connected to the voltage reference
and is not available for external connection. The amplifier is
designed for an open loop gain of 80dB, along with a typical
bandwidth of 1.7MHz and 49 degrees of phase margin. The
boost output voltage of the power factor pre-regulator is di-
vided down and monitored by the inverting input. Input bias
current (0.5A max) can cause an output voltage error that is
equal to the product of the input bias current and the value of
the upper divider resistor. The amplifier's output is available
for external loop compensation. Typically, the loop bandwidth
is set below 10Hz in order to reject the low frequency ripple
associated with 2X the line frequency.
For example, if the
error amplifier is configured as an integrator with 1.2Hz band-
width, it will have 40dB ripple rejection at 120Hz frequency.
This means that if the output of the error amp is allowed to
have 100mV of ripple, the boost converter must be limited to
less than 10V of ripple on its output.
To prevent boost output run away condition that may occur
during removal of the output load, a separate comparator moni-
tors the E.A. output voltage and compares it to an internal 1.8V
reference. When load is removed, E.A. output swings lower
than 1.8V, trips the comparator and turns output driver off till
the inverting input voltage drops below 2.5V. At this point, the
E.A. output swings positive, turns the output driver back on
and repeats the cycle until the load is returned to normal con-
dition.
To reduce output overshoot during line and load transients,
the E.A. output is clamped to two diode drops above the refer-
ence voltage.
This prohibits the amplifier from being satu-
rated, allowing it to recover faster thus minimizing the boost
voltage overshoot.
VOLTAGE REFERENCE
(continued)
V
HYST
C1
DISCHARGE
V
START
BOOTSTRAP
WINDING
R
T & CT TIME CONSTANT
V
C1
t
DISCHARGE
TIME
FIGURE 25 — START-UP CAPACITOR VOLTAGE
VOLTAGE REFERENCE
The voltage reference is a low drift bandgap design which pro-
vides a stable +2.5V output with maximum of ±1.5% initial ac-
curacy. This voltage is internally tied to the non-inverting in-
put of the amplifier and is not available for external connec-
tion. The initial accuracy of the reference includes error am-
plifier input offset voltage. Figure 26 shows typical variation of
the reference voltage vs. temperature.
FIGURE 27 — THE AMPLIFIER CONFIGURED AS AN INTEGRATOR
FOR LOOP COMPENSATION
From I
DET Logic
1.8V
OUTPUT
DRIVE
7
1
2
V
REF
C4
V
O
I
9
R9
R10
Bias
BW =
1
2
π R
9 C4
I
9 >> IBIAS
2f
f = Line Freq.
2.47
2.45
(T
A)
Ambient Temperature - (°C)
2.52
(V
R)
Reference
Voltage
-
(V)
2.48
-50
-25
0
25
50
75
100
125
V
CC = 12V
C
L = 1nF
2.46
2.49
2.50
2.51
FIGURE 26 — REFERENCE VOLTAGE (Including Offset) vs. TEMPERATURE
O
B
SO
LETE
PRO
D
UCT
NOT
RECOMMENDED
FOR
NEW
DESIGNS
相关PDF资料 |
PDF描述 |
|---|---|
| LX1562IM | 0.5 A POWER FACTOR CONTROLLER, PDIP8 |
| LX1562IDM | 0.5 A POWER FACTOR CONTROLLER, PDSO8 |
| LX1570IDM-TR | 1 A SWITCHING CONTROLLER, PDSO8 |
| LX1571CDM-TR | 1 A SWITCHING CONTROLLER, PDSO8 |
| LX1571IDM-TR | 1 A SWITCHING CONTROLLER, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LX1563IM | 功能描述:IC CONTROLLER PFC 9.8V 8DIP RoHS:是 类别:集成电路 (IC) >> PMIC - PFC（功率因数修正） 系列:- 产品培训模块:GreenChip Synchronous Rectification Control Family of ICs 标准包装:1 系列:- 模式:间歇导电（DCM） 频率 - 开关:- 电流 - 启动:- 电源电压:8.6 V ~ 38 V 工作温度:-20°C ~ 150°C 安装类型:表面贴装 封装/外壳:14-SOIC（0.154"，3.90mm 宽） 供应商设备封装:14-SO 包装:Digi-Reel® 其它名称:568-5348-6 |
| LX1570 | 制造商:MICROSEMI 制造商全称:Microsemi Corporation 功能描述:PHASE MODULATED AC SYNCHRONOUS SECONDARY-SIDE CONTROLLER |
| LX1570CDM | 功能描述:IC REG CTRLR ISO PWM CM 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| LX1570CM | 功能描述:IC REG CTRLR ISO PWM CM 8-DIP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| LX1570IDM | 功能描述:IC REG CTRLR ISO PWM CM 8-SOIC RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。