- 您现在的位置：买卖IC网 > PDF目录67759 > LX1672-03CLQ-TR (MICROSEMI CORP-ANALOG MIXED SIGNAL GROUP) 1 A DUAL SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PQCC38 PDF资料下载
参数资料
| 型号： | LX1672-03CLQ-TR |
| 厂商： | MICROSEMI CORP-ANALOG MIXED SIGNAL GROUP |
| 元件分类： | 稳压器 |
| 英文描述： | 1 A DUAL SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PQCC38 |
| 封装： | ROHS COMPLIANT, PLASTIC, MLPQ-38 |
| 文件页数： | 10/20页 |
| 文件大小： | 382K |
| 代理商： | LX1672-03CLQ-TR |
PRODUCTION DATA SHEET
Microsemi
Integrated Products Division
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 18
Copyright
2000
Rev. 1.0, 2005-08-10
WWW
.Microse
m
i
.CO
M
LX1672
Multiple Output LoadSHARE PWM
TM
APPLICATION NOTE CONSI D E R ATI O NS
1.
The power N-MOSFET transistor’s total gate charge spec,
(Qg) should not exceed 40Nc when VCx = +12V.
This
condition will guarantee operation over the specified ambient
temperature range.
The Qg value of the N-MOSFET is
directly related to the amount of power dissipation inside the
IC package, from the two sets of MOSFET drivers. The
equation relating Qg to the power dissipation of a MOSFET
driver is: Pd = f * Qg * Vd . f = 300KHs and Vd is the
supply voltage for the MOSFET driver. The two bottom
MOSFET drivers are powered by the VCCL pin that is
connected to +5V.
The upper MOSFET drivers can be
connected to the +12V supply or to a bootstrap supply
generated by its output bridge. The bootstrap supply will be at
+17V.
Depending on the thermal environment of the
application circuit, the Qg value of the N-MOSFETs will have
to be less than the 40nC value. A typical configuration of the
input voltage rails to generate the output voltages required is
having the 5volt supply on phase 1 and the 3.3 volt supply on
phase 2. At the max Qg value, the two bottom MOSFET
drivers will dissipate 60mw each. The upper MOSFET drivers
for phases 1 and 2 operate off of +12volts. Their dissipation
is 144mw each. The total power dissipation for gate drive is
408 mw. Icc x Vcc =15ma x 5 V= 75mW. Total package
power dissipation = 483mW. Using the thermal equation of:
TJ = TA + Pd * Oja, the Junction temperature for this IC
package is = 23 + .483 * 85 which = 64°C. This means that
the ambient temperature rise has to be less than 86°C.
2.
The Soft-Start reference input has a 300mv threshold, above
which the PWM starts to operate. The internal operating
reference level is set at 800mV. This means that the output
voltage is 37.5% low when the PWM becomes active. This
starts each phase up in the current limit mode without Hiccup
operation. If more than one phase is using the 5volt rail for
conversion, then their soft-start capacitor values should be
changed so that the two phases do not start up together. This
will help reduce the amount of 5 volt input capacitance
required. Also the VCC pin and the VCCL pin should be kept
separated and should be decoupled separately.
This will
prevent the VCC pin from drooping back below the UVLO set
point during start up.
3.
If a phase is not used connect VSX and VCX pins to VCC.
Do not leave them floating. A floating VSX pin will result in
operation resembling a hiccup condition.
4.
When phases 1 and 2 are used in the Bi-phase mode to current
share into the same output load, the phase 2 current is forced to
follow the phase 1 current. It is important to use a larger soft-
start capacitor on phase 2 than phase 1 so that the phase 1
current becomes active before phase 2 becomes active. This will
minimize any start up transient. It is also important to disable
phase 1 and 2 at the same time. Disabling phase 1 without
disabling phase 2, in the Bi-phase mode, allows phase 2 to turn
on and off randomly because it has lost its reference.
5.
The minimum RSET resistor value is 1k ohm for the current
limit sensing.
If this resistor becomes shorted, it will do
permanent damage to the IC.
6.
A resistor has been put in series with the gate of the LDO pass
transistor to reduce the output noise level. The resistor value
can be changed to optimize the output transient response versus
output noise.
7.
The LDO controller inside the IC uses the voltage at VC1 as
the drive voltage.
Due to noise considerations ideally the
voltage on the VC1 pin would be a fixed +12volt supply. When
VC1 is connected to a bootstrap supply the LDO output will
reflect significant switching noise without filtering.
8.
To delay the turn on of the LDO controller output, a capacitor
should be connected between the LDDIS pin and the +5volts.
The LDDIS input has a 100K pull down resistor, which keeps
the LDO active until this pin is pulled high. During the power
up sequence the capacitor connected to the LDDIS pin will keep
the LDO off until this capacitor, being charge by the 100K pull
down resistor, goes through the low input threshold level.
AA
PP
LL
IICC
AA
TT
IIOO
NN
相关PDF资料 |
PDF描述 |
|---|---|
| LX1673-06CLQT | 1 A SWITCHING CONTROLLER, 690 kHz SWITCHING FREQ-MAX, PQCC20 |
| LX1673-03CLQT | 1 A SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PQCC20 |
| LX1673-09CLQT | 1 A SWITCHING CONTROLLER, 1035 kHz SWITCHING FREQ-MAX, PQCC20 |
| LX1676-CLQTR | 1.5 A SWITCHING CONTROLLER, 1100 kHz SWITCHING FREQ-MAX, PQCC38 |
| LX1676-CPWTR | 1.5 A SWITCHING CONTROLLER, 1100 kHz SWITCHING FREQ-MAX, PDSO38 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LX1672-03CPW | 功能描述:IC REG CTRLR BUCK PWM VM 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:LoadSHARE™ 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LX1672-03CPW-TR | 制造商:Microsemi Corporation 功能描述:MOSFET DRVR 0.8V 1A 3-OUT HI/LO SIDE HALF BRDG NON-INV 28TSS - Tape and Reel |
| LX1672-05CPW | 功能描述:IC REG CTRLR BUCK PWM VM 28TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:LoadSHARE™ 特色产品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 标准包装:1 系列:PowerWise® PWM 型:电压模式 输出数:1 频率 - 最大:1MHz 占空比:81% 电源电压:4.5 V ~ 18 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-5°C ~ 125°C 封装/外壳:32-WFQFN 裸露焊盘 包装:Digi-Reel® 产品目录页面:1303 (CN2011-ZH PDF) 其它名称:LM3754SQDKR |
| LX1672-05CPW-TR | 制造商:Microsemi Corporation 功能描述:MOSFET DRVR 0.8V 1A 3-OUT HI/LO SIDE HALF BRDG NON-INV 28TSS - Tape and Reel |
| LX1672-06CLQ | 功能描述:IC REG CTRLR BUCK PWM VM 38MLPQ RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:LoadSHARE™ 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。