参数资料
型号: LX1673-06CLQT
厂商: MICROSEMI CORP-ANALOG MIXED SIGNAL GROUP
元件分类: 稳压器
英文描述: 1 A SWITCHING CONTROLLER, 690 kHz SWITCHING FREQ-MAX, PQCC20
封装: PLASTIC, MLPQ-20
文件页数: 4/15页
文件大小: 302K
代理商: LX1673-06CLQT
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 12
Copyright
2000
Rev. 0.2j, 2002-07-17
WWW
.M
ic
ro
sem
i
.COM
LX1673
High Frequency PWM Regulator
PRELIMINARY
INTEGR A T E D
PR ODU C T S
APPLI CATION NOT E
APPLI CATION NOT E (CON T I NUE D)
(CON T I NUE D)
OUTPUT DISABLE
The LX1673 PWM MOSFET driver outputs are shut off by
pulling the disable (DIS) pin above 1.2V. There is a 80K
pulldown resistor on this input.
The LDO voltage regulator has its own Disable pin (LDDIS)
for control of this output voltage. Pulling this pin above 3 V
disables the LDO. There is a 100K
pulldown resistor on this
input.
PROGRAMMING THE OUTPUT VOLTAGE
The output Voltage is sensed by the feedback pin (FBX) which
is compared to a 0.8V reference. The output voltage can be set to
any voltage above 0.8V (and lower than the input voltage) by
means of a resistor divider (see Figure 1).
)
/R
R
(1
V
2
1
REF
OUT
+
=
Note: This equation is simplified and does not account for
error amplifier input current. Keep R1 and R2 close to 1k (order
of magnitude).
DDR VTT TERMINATION VOLTAGE
Double Data Rate (DDR) SDRAM requires a termination
voltage (VTT) in addition to the line driver supply voltage (VDDQ)
and receiver supply voltage (VDD).
Although it is not a
requirement VDD is generally equal to VDDQ so that only VTT
and VDDQ are required..
VTT for DDR memory can be generated with the LX1673 by
using the positive input of the phase 2 error amplifier RF2 as a
reference input from an external reference voltage VREF which is
defined as one half of VDDQ. Using VREF as the reference input
will insure that all voltages are correct and track each other as
specified in the JEDEC (EIA/JESD8-9A) specification. The phase 2
output will then be equal to VREF and track the VDDQ supply as
required.
When an external reference is used the connection between the
error amplifier positive input and the Soft Start pin is lost and Soft
Start will not function. It is recommended that the external
reference voltage have an R-C time constant that will be long
enough to allow the output capacitor to charge slowly.
See Microsemi Application Note 17 for more details.
AA
PP
LL
IICC
AA
TT
IIOO
NN
SS
相关PDF资料
PDF描述
LX1673-03CLQT 1 A SWITCHING CONTROLLER, 345 kHz SWITCHING FREQ-MAX, PQCC20
LX1673-09CLQT 1 A SWITCHING CONTROLLER, 1035 kHz SWITCHING FREQ-MAX, PQCC20
LX1676-CLQTR 1.5 A SWITCHING CONTROLLER, 1100 kHz SWITCHING FREQ-MAX, PQCC38
LX1676-CPWTR 1.5 A SWITCHING CONTROLLER, 1100 kHz SWITCHING FREQ-MAX, PDSO38
LX1732CDUT 1 A SWITCHING REGULATOR, 135 kHz SWITCHING FREQ-MAX, PDSO8
相关代理商/技术参数
参数描述
LX1673-06CLQ-TR 制造商:Microsemi Corporation 功能描述:VOLT MODE PWM CNTRLR 0.8V TO 5.5V 1A 20MLPQ - Tape and Reel
LX1673-06CPW 功能描述:IC REG DL BCK/LINEAR 20TSSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压(降压)同步(3),线性(LDO)(2) 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:*
LX1673-06CPW-TR 制造商:Microsemi Corporation 功能描述:VOLT MODE PWM CNTRLR 0.8V TO 5.5V 1A 20TSSOP - Tape and Reel
LX1673-09CLQ 功能描述:IC REG DL BCK/LINEAR SYNC 20MLPQ RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压(降压)同步(2),线性(LDO)(1) 功能:任何功能 输出数:3 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:4.5 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:28-TSSOP(0.173",4.40mm 宽) 供应商设备封装:* 包装:带卷 (TR) 其它名称:ISL6402IVZ-TTR
LX1673-09CLQ-TR 制造商:Microsemi Corporation 功能描述:VOLT MODE PWM CNTRLR 0.8V TO 5.5V 1A 20MLPQ - Tape and Reel