- 您现在的位置：买卖IC网 > PDF目录369877 > LX1673-06CPW PWM Controllers PDF资料下载
参数资料
| 型号： | LX1673-06CPW |
| 英文描述： | PWM Controllers |
| 中文描述： | PWM控制器 |
| 文件页数： | 18/21页 |
| 文件大小： | 554K |
| 代理商： | LX1673-06CPW |
Microsemi
Integrated Products, Power Management
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 18
Copyright
2000
Rev. 0.5i, 2002-07-17
W
M
.
C
LX1671
Multiple Output LoadSHARE PWM
P
RELIMINARY
I N T E G R A T E D P R O D U C T S
APPLICATION NOTE
(CONTINUED)
O
UTPUT
E
NABLE
The LX1671 MOSFET driver outputs are shut off by pulling
the soft-start pin below 0.3V.
The LDO voltage regulator has its own Enable/Disable pin
(LDDIS) for control of this output voltage.
P
ROGRAMMING
T
HE
O
UTPUT
V
OLTAGE
The output Voltage is sensed by the feedback pin (FB
X
) which
is compared to a 0.8V reference. The output voltage can be set to
any voltage above 0.8V (and lower than the input voltage) by
means of a resistor divider R1-R2 (see Figure 1).
)
/R
R
(1
V
V
2
1
REF
OUT
+
=
Note: This equation is simplified and does not account for
error amplifier input current. Keep R
1
and R
2
close to 1k
(order
of magnitude).
AN 18
For more information see Microsemi Application Note 18
LX1671 Product design Guide
DDR V
TT
T
ERMINATION
V
OLTAGE
Double Data Rate (DDR) SDRAM requires a termination
voltage (V
TT
)
in addition to the line driver supply voltage (VDDQ)
and receiver supply voltage (VDD). Although it is not a
requirement VDD is generally equal to VDDQ so that only V
TT
and VDDQ are required..
The LX1671 can supply both voltages by using two of the three
PWM phases. Since the currents for V
TT
and (VDD plus VDDQ)
are quite often several amps, (2A to 6A is common) a switching
regulator is a logical choice
V
TT
for DDR memory can be generated with the LX1671 by
using the positive input of the phase 2 error amplifier RF2 as a
reference input from an external reference voltage V
REF
which is
defined as one half of VDDQ. Using V
REF
as the reference input
will insure that all voltages are correct and track each other as
specified in the JEDEC (EIA/JESD8-9A) specification. The phase 2
output will then be equal to V
REF
and track the VDDQ supply as
required.
When an external reference is used the Soft Start will not be
functional for that phase
See Microsemi Application Note 17 for more details.
A
P
P
L
I
C
A
T
I
O
N
S
相关PDF资料 |
PDF描述 |
|---|---|
| LX1673-09CLQ | PWM Controllers |
| LX1673-09CPW | PWM Controllers |
| LX1676CLQ | PWM Controllers |
| LX1676CPW | PWM Controllers |
| LX1677CLQ | PWM Controllers |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LX1673-06CPW-TR | 制造商:Microsemi Corporation 功能描述:VOLT MODE PWM CNTRLR 0.8V TO 5.5V 1A 20TSSOP - Tape and Reel |
| LX1673-09CLQ | 功能描述:IC REG DL BCK/LINEAR SYNC 20MLPQ RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（2），线性（LDO）（1） 功能:任何功能 输出数:3 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:4.5 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:28-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:* 包装:带卷 (TR) 其它名称:ISL6402IVZ-TTR |
| LX1673-09CLQ-TR | 制造商:Microsemi Corporation 功能描述:VOLT MODE PWM CNTRLR 0.8V TO 5.5V 1A 20MLPQ - Tape and Reel |
| LX1673-09CPW | 功能描述:IC REG DL BCK/LINEAR 20TSSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（2），线性（LDO）（1） 功能:任何功能 输出数:3 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:4.5 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:28-TSSOP（0.173"，4.40mm 宽） 供应商设备封装:* 包装:带卷 (TR) 其它名称:ISL6402IVZ-TTR |
| LX1673-09CPW-TR | 制造商:Microsemi Corporation 功能描述:VOLT MODE PWM CNTRLR 0.8V TO 5.5V 1A 20TSSOP - Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。