- 您现在的位置：买卖IC网 > PDF目录69008 > LX1741CLM-TR (MICROSEMI CORP-ANALOG MIXED SIGNAL GROUP) 0.145 A SWITCHING CONTROLLER, PDSO8 PDF资料下载
参数资料
| 型号： | LX1741CLM-TR |
| 厂商： | MICROSEMI CORP-ANALOG MIXED SIGNAL GROUP |
| 元件分类： | 稳压器 |
| 英文描述： | 0.145 A SWITCHING CONTROLLER, PDSO8 |
| 封装： | PLASTIC, MLP-8 |
| 文件页数： | 14/15页 |
| 文件大小： | 479K |
| 代理商： | LX1741CLM-TR |
Microsemi
Integrated Products Division
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 8
Copyright
2000
Rev. 1.1b, 2005-03-03
WWW
.Microse
m
i
.CO
M
LX1741
High Efficiency High Voltage Boost Controller
PRODUCTION DATA SHEET
I N T E GRA T ED
PR ODUC T S
APPLICATION IN FORMATION (CONTINUED )
OUTPUT RIPPLE CAPACITOR SELECTION
Output voltage ripple is a function of the inductor value
(L), the output capacitor value (COUT), the peak switch
current setting (IPEAK), the load current (IOUT), the input
voltage (VIN) and the output voltage (VOUT) for a this
boost converter regulation scheme. When the switch is
first turned on, the peak-to-peak voltage ripple is a
function of the output droop (as the inductor current
charges to IPEAK), the feedback transition error (i.e.,
typically 10mV), and the output overshoot (when the
stored energy in the inductor is delivered to the load at the
end of the charging cycle). Therefore the total ripple
voltage is
VRIPPLE = VDROOP + VOVERSHOOT + 10mV
The initial droop can be estimated as follows where the
0.5v value in the denominator is an estimate of the voltage
drop across the inductor and the FET’s RDS_ON:
()
0.5
V
I
C
L
V
IN
OUT
PK
OUT
DROOP
×
=
The output overshoot can be estimated as follows
where the 0.5 value in the denominator is an estimate of
the voltage drop across the diode:
()
IN
OUT
2
OUT
PK
OUT
2
1
OVERSHOOT
V
0.5
V
I
C
L
V
+
×
×
=
DESIGN EXAMPLE:
Determine the VRIPPLE where IPK equals 200mA, IOUT
equals 35mA, L equals 47H, COUT equals 4.7F, VIN
equals 3.0V, and VOUT equals 18.0V:
()
mV
8
2
0.5
3.0
35mA
200mA
F
4.7
H
47
VDROOP
=
×
=
()
mV
4
.
9
0
.
3
0.5
0
.
8
1
mA
5
3
mA
200
F
4.7
H
47
V
2
1
OVERSHOOT
=
+
×
×
=
Therefore, for COUT equals 4.7F:
VRIPPLE = 28mV + 9.4mV + 10mV = 47.4mV
Increasing the output capacitor value results in the
reduction of the output voltage ripple voltage. Low ESR
capacitors are recommended to reduce ripple caused by the
switching current.
Multi-layer ceramic capacitors with
X5R or X7R dielectric are a superior choice featuring small
size, very low ESR, and a temperature stable dielectric.
Low ESR electrolytic capacitors such as solid tantalum or
OS-CON types are also acceptable. Moreover, adding a
capacitor from the output to the feedback pin (C2) allows
the internal feedback circuitry to respond faster which
further minimizes output voltage ripple and reduces noise
coupling into the high impedance feedback input.
DIODE SELECTION
A Schottky diode is recommended for most applications
(e.g. Microsemi UPS5819). The low forward voltage drop
and fast recovery time associated with this device supports
the switching demands associated with this circuit topology.
The designer is encouraged to consider the diode’s average
and peak current ratings with respect to the application’s
output and peak inductor current requirements. Further, the
diode’s reverse breakdown voltage characteristic must be
capable of withstanding a negative voltage transition that is
greater than VOUT.
TRANSISTOR SELECTION
The LX1741 can drive up to 100mA of gate drive
current. An N-channel MOSFET with a relatively low
threshold voltage, low gate charge and low RDS(ON) is
required to optimize overall circuit performance.
The
LXE1741 Evaluation Board uses a Fairchild FDV303. This
NMOS device was chosen because it demonstrates an
RDS_ON of 0.33 and a total gate charge Qg of 1.64nC (typ.).
PCB LAYOUT
The LX1741 produces high slew-rate voltage and current
waveforms hence; the designer should take this into
consideration when laying out the circuit. Minimizing trace
lengths from the IC to the inductor, transistor, diode, input
and output capacitors, and feedback connection (i.e., pin 6)
are typical considerations. Moreover, the designer should
maximize the DC input and output trace widths to
accommodate peak current levels associated with this
circuit.
AA
PP
LL
IICC
AA
TT
IIOO
NN
SS
相关PDF资料 |
PDF描述 |
|---|---|
| LX1741CDU-TR | 0.145 A SWITCHING CONTROLLER, PDSO8 |
| LX1882-00CDMT | SWITCHED CAPACITOR REGULATOR, 620 kHz SWITCHING FREQ-MAX, PDSO8 |
| LX1882-33CDUT | SWITCHED CAPACITOR REGULATOR, 620 kHz SWITCHING FREQ-MAX, PDSO8 |
| LX1882-00CDUT | SWITCHED CAPACITOR REGULATOR, 620 kHz SWITCHING FREQ-MAX, PDSO8 |
| LX1882-33CDMT | SWITCHED CAPACITOR REGULATOR, 620 kHz SWITCHING FREQ-MAX, PDSO8 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| LX1742 | 制造商:MICROSEMI 制造商全称:Microsemi Corporation 功能描述:High Efficiency High Voltage Boost Controller |
| LX1742 EVAL KIT | 制造商:Microsemi Corporation 功能描述:EVAL KIT FOR LX1742 - Bulk |
| LX1742CDU | 功能描述:IC REG BOOST ADJ 8MSOP RoHS:是 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 开关稳压器 系列:- 产品培训模块:High Efficiency Current Mode Switching Regulators CMOS LDO Regulators 特色产品:BD91x Series Step-Down Regulators 标准包装:2,500 系列:- 类型:降压（降压） 输出类型:两者兼有 输出数:2 输出电压:3.3V，0.8 V ~ 2.5 V 输入电压:4.5 V ~ 5.5 V PWM 型:电流模式 频率 - 开关:1MHz 电流 - 输出:1.5A 同步整流器:是 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:20-VFQFN 裸露焊盘 包装:带卷 (TR) 供应商设备封装:VQFN020V4040 产品目录页面:1373 (CN2011-ZH PDF) 其它名称:BD9152MUV-E2TR |
| LX1742EVALKIT | 制造商:未知厂家 制造商全称:未知厂家 功能描述:DC:DC Converter |
| LX1744 | 制造商:MICROSEMI 制造商全称:Microsemi Corporation 功能描述:Dual Output Boost ? LED Driver / LCD Bias |
发布紧急采购，3分钟左右您将得到回复。