PRODUCTION DATASHEET
Microsemi
Integrated Products
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 2
Copyright
2002
Rev. 1.0b, 2005-01-17
WWW
.Microse
m
i
.CO
M
PanelMatch
LXM1618-12-6x
12V 6W CCFL Programmable Inverter Module
I N TE G R A T E D
P R O D U C TS
ABSOLUTE MAXI MUM RATI NGS (NOTE 1)
Input Signal Voltage (VIN1).....................................................................................................................................-0.3V to 15V
Input Power .................................................................................................................................................................... 8.25W
Output Voltage, no load ............................................................................................................ Internally Limited to 1800VRMS
Output Current .............................................................................................................................10mARMS (Internally Limited)
Output Power ................................................................................................................................................................... 6.0W
Input Signal Voltage (
SLEEP Input) ..................................................................................................................... -0.3V to VIN1
Input Signal Voltage (BRITE) ...............................................................................................................................-0.3V to 5.5V
Ambient Operating Temperature, zero airflow.....................................................................................................-20°C to 70°C
Storage Temperature Range...............................................................................................................................-40°C to 85°C
Note 1: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of specified
terminal.
RECOMM END E D O P ERATI NG CONDI T I ONS ( R .C.)
This module has been designed to operate over a wide range of input and output conditions. However, best efficiency and performance
will be obtained if the module is operated under the condition listed in the ‘R.C.’ column. Min. and Max. columns indicate values beyond
which the inverter, although operational, will not function optimally.
Recommended Operating Conditions
Parameter
Symbol
Min
R.C.
Max
Units
Input Supply Voltage Range (Fully Regulated
Lamp Current)
10.8
12
13.2
Input Supply Voltage Range (Functional)
VIN1
10.2
12
13.8
V
Output Power
PO
6.0
W
Linear BRITE Control Input Voltage Range
VBRT_ADJ
0.65 to 0.9
2.0
V
Lamp Operating Voltage
VLAMP
545
640
735*
VRMS
Lamp Current (Full Brightness)
IOLAMP
5
8
mARMS
Operating Ambient Temperature Range
TA
-20
70
°C
The minimum VBRT ADJ voltage depends on the panel characteristics, depending on the panel it can vary from 0.65V to 0.9V
* Total output power must not exceed 6W. Higher voltage lamps may require maximum output current to be set lower than 8mARMS
ELECTRI CAL CHA RACTERI S TI CS
Unless otherwise specified, the following specifications apply over the recommended operating condition and ambient temperature of
25
°C except where otherwise noted.
LXM1618-12-6x
Parameter
Symbol
Test Conditions
Min
Typ
Max
Units
OUTPUT PIN CHARACTERISTICS
Full Bright Lamp Current
IL(MAX)
VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 12VDC
ISET1 = Ground, ISET2 = Ground
4.4
5
5.6
mARMS
Full Bright Lamp Current
IL(MAX)
VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 12VDC
ISET1 = Ground, ISET2 = Open
5.4
6
6.6
mARMS
Full Bright Lamp Current
IL(MAX)
VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 12VDC
ISET1 = Open, ISET2 = Ground
6.4
7
7.6
mARMS
Full Bright Lamp Current
IL(MAX)
VBRT_ADJ > 2.0VDC, SLEEP > 2.0V, VIN1 = 12VDC
ISET1 = Open, ISET2 = Open
7.4
8
8.6
mARMS
Min. Average Lamp Current
IL(MIN)
VBRT_ADJ = 0.65VDC, SLEEP > 2.0V, VIN1 = 12VDC
ISET1 = ISET2 = Ground
1.5 *
mARMS
Lamp Start Voltage
VLS
-20°C < TA < 70°C, VIN1 > 10.8VDC
1400
1650
VRMS
Operating Frequency
fO
VBRT_ADJ = 2.5VDC, SLEEP > 2.0V, VIN1 = 12V
57
60
63
kHz
* The inverter is capable of a lower output current than may be recommended by the panel manufacturer. It is the user’s responsibility to set
the minimum brightness (BRITE) input at or above the panel specification for minimum current.
EE
LL
EE
CC
TT
RR
IICC
AA
LL
SS