- 您现在的位置：买卖IC网 > PDF目录9705 > M-986-2A1P (IXYS Integrated Circuits Division)IC TRANSCEIVER MF 2CHAN 40-DIP PDF资料下载
参数资料
| 型号： | M-986-2A1P |
| 厂商： | IXYS Integrated Circuits Division |
| 文件页数： | 9/13页 |
| 文件大小： | 0K |
| 描述： | IC TRANSCEIVER MF 2CHAN 40-DIP |
| 产品变化通告： | M-986 Transceiver Obsolescence 3/Feb/2011 |
| 标准包装： | 9 |
| 类型： | 收发器 |
| 驱动器/接收器数： | 2/2 |
| 电源电压： | 4.75 V ~ 5.25 V |
| 安装类型： | 通孔 |
| 封装/外壳： | 40-DIP（0.600"，15.24mm） |
| 供应商设备封装： | 40-DIP |
| 包装： | 管件 |
M-986-2A1
www.clare.com
5
Rev. 3
Signal Description
Signal
Pin
I/O/Z
Description
D15-D8
18-11
I/O/Z
Unused. Leave open.
D7-D0
19-26
I/O/Z
8-bit coprocessor latch.
TBLF
40
O
Transmit buffer latch full flag.
RBLE
1
O
Receive buffer latch empty flag.
HI/LO
2
I
Latch byte select pin. Tie low.
BIO
9
I
Unused. Leave open.
RD
32
I/O
Used by the external processor to read from the coprocessor latch by driving the
RD line active (low), thus enabling the output latch to drive the latched data.
When the data has been read, the external device must bring the RD line high.
EXINT
5
I
Unused. Leave open.
MC
3
I
Microcomputer mode select pin. Tie low.
MC/PM
27
I
Coprocessor mode select pin. Tie low.
RS
4
I
Reset input for initializing the device. When an active low is placed on RS pin for
a minimum of five clock cycles, RD and WR are forced high, and the data bus
(LD7 through LD0) goes to a high impedance state. The serial port clock and
transmit outputs also go to the high impedance state.
WR
31
I/O
Used by the external processor to write data to the coprocessor port. To write
data the external processor drives the WR line low, places data on the data bus,
and then drives the WR line high to clock the data into the on-chip latch.
XF
28
O
Watchdog signal. Toggles at least once every 10 milliseconds when the
processor is functioning properly. If the pin is not toggled at least once every 10
ms, the processor is lost and should be reset.
CLKOUT
6
O
System clock output (one-fourth crystal/CLKIN frequency, nominally 5.12 MHz).
V
SS
10
I
Ground pin.
V
CC
30
I
5V supply pin.
X1
7
O
Crystal output pin for internal oscillator. If the internal oscillator is not used, this
pin should be left unconnected.
X2/CLKIN
8
I
Input pin to the internal oscillator (X2) from the crystal. Alternatively, an input pin
for the external oscillator (CLKIN).
DR1 & DR0
33 & 29
I
Serial-port receive-channel inputs. 2.048 MHz serial data is received in the receive
registers via these pins. DR0 = channel 1; DR1 = channel 2.
FR
37
O
8 kHz internal serial-port framing output. If internal clocking is selected,
serial-port transmit and receive operations occur simultaneously on an active
(high) FR framing pulse.
DX1 & DX0
36 & 35
O
Serial-port transmit-channel outputs. 2.048 MHz serial data is transmitted from
the transmit registers on these pins. These outputs are in the high-impedance
state when not transmitting. DX0 = channel 1; DX1 = channel 2.
FSR
39
I
8 kHz external serial-port receive-framing input. If external clocking is selected,
data is received via the receive pins (DR1 and DR0) on the active (low) FSR input.
The falling edge of FSR initiates the receive process, and the rising edge causes
the M-986 to process the data.
SCLK
34
I/O/Z
2.048 MHz serial-port clock. Master clock for transmitting and receiving serial-
port data. Configured as an input in external clocking mode or output in internal
clocking mode. Reset (RS) forces SCLK to the high-impedance state.
FSX
38
I
8 kHz external serial-port transmit-framing input. If external clocking is enabled,
data is transmitted on the transmit pins (DX1, DX0) on the active (low) input. The
falling edge of FSX initiates the transmit process, and the rising edge causes the
M-986 to internally load data for the next cycle.
相关PDF资料 |
PDF描述 |
|---|---|
| MS3451W20-4S | CONN RCPT 4POS CBL MNT W/SCKT |
| MS3451L20-4S | CONN RCPT 4POS CBL MNT W/SCKT |
| LTC1324CS | IC TXRX LOCALTALK 5V SNGL 16SOIC |
| MS27484E14B15P | CONN PLUG 15POS STRAIGHT W/PINS |
| MC100EP16VCDT | IC RCVR/DRVR ECL DIFF 5V 8TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M-986-2A1PL | 功能描述:固态继电器-PCB安装 MF Transceiver, dual channel, 44xpin RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT |
| M-986-2R2 | 制造商:CLARE 制造商全称:Clare, Inc. 功能描述:MFC Transceivers |
| M-986-2R2P | 功能描述:固态继电器-PCB安装 MF Transceiver, dual channel, 40xpin RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT |
| M-986-2R2PL | 功能描述:固态继电器-PCB安装 MF Transceiver, dual channel, 44xpin RoHS:否 制造商:Omron Electronics 控制电压范围: 负载电压额定值:40 V 负载电流额定值:120 mA 触点形式:1 Form A (SPST-NO) 输出设备:MOSFET 封装 / 箱体:USOP-4 安装风格:SMD/SMT |
| M9866 | 制造商:Tamura Corporation of America 功能描述: |
发布紧急采购，3分钟左右您将得到回复。