- 您现在的位置：买卖IC网 > PDF目录149420 > M1034-16I161.1328 (INTEGRATED DEVICE TECHNOLOGY INC) 1034 SERIES, PLL BASED CLOCK DRIVER, 1 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), CQCC36 PDF资料下载
参数资料
| 型号： | M1034-16I161.1328 |
| 厂商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分类： | 时钟及定时 |
| 英文描述： | 1034 SERIES, PLL BASED CLOCK DRIVER, 1 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), CQCC36 |
| 封装： | 9 X 9 MM, CERAMIC, LCC-36 |
| 文件页数： | 10/14页 |
| 文件大小： | 200K |
| 代理商： | M1034-16I161.1328 |
M1033/34 Preliminary Information 0.1
5 of 14
Revised 07Apr2005
Integr ated Circuit Systems , Inc. ● Netw o r ki ng & C o mmun ica t io ns ● ww w. icst.com ● tel (5 08) 85 2-54 00
M1033/34
VCSO BASED CLOCK PLL WITH AUTOSWITCH
Preliminar y In f o r m atio n
Integrated
Circuit
Systems, Inc.
Input Reference Clocks
Two clock reference inputs and a selection mux are
provided. Either reference clock input can accept a
differential clock signal (such as LVPECL or LVDS) or
a single-ended clock input (LVCMOS or LVTTL on the
non-inverting input).
A single-ended reference clock on the unselected
reference input can cause an increase in output
clock jitter. For this reason, differential reference
inputs are preferred; interference from a differential
input on the non-selected input is minimal.
Implementation of single-ended input has been
facilitated by biasing nDIF_REF0 and nDEF_REF1 to Vcc/2,
with 50k
to Vcc and 50k to ground. Figure 4 shows
the input clock structure and how it is used with either
LVCMOS / LVTTL inputs or a DC- coupled LVPECL
clock.
Figure 4: Input Reference Clocks
Differential LVPECL Inputs
Differential LVPECL inputs are connected to both
reference input pins in the usual manner. The external
load termination resistors shown in Figure 4 (the 127
and 82
resistors) will work for both AC and DC
coupled LVPECL reference clock lines. These provide
the 50
load termination and the VTT bias voltage.
Single-ended Inputs
Single-ended inputs (LVCMOS or LVTTL) are
connected to the non-inverting reference input pin
(DIF_REF0 or DIF_REF1). The inverting reference input pin
(nDIF_REF0 or nDIF_REF1) must be left unconnected.
In single-ended operation, when the unused inverting
input pin (nDIF_REF0 or nDEF_REF1) is left floating (not
connected), the input will self-bias at VCC/2.
PLL Operation
The M1033/34 is a complete clock PLL. It uses a phase
detector and configurable dividers to synchronize the
output of the VCSO with the selected reference clock.
The “M” divider divides the VCSO output frequency,
feeding the result into the non-inverting input of the
phase detector. The output of the “R” divider is fed into
the inverting input of the phase detector. The phase
detector compares its two inputs. The phase detector
output, filtered externally, causes the VCSO to increase
or decrease in speed as needed to phase- and
frequency-lock the VCSO to the reference input.
The value of the M divider directly affects closed loop
bandwidth.
The relationship between the nominal VCSO center
frequency (Fvcso), the M divider, the R divider, and the
input reference frequency (Fin) is:
For the available M divider and R divider look-up table
combinations, Tables 3 and 4 on pg. 3 list the Total PLL
Ratio as well as Fin when using the M1033-11-155.5200 or
the M1034-11-155.5200. (“Ordering Information”, pg. 14.)
Due to the narrow tuning range of the VCSO
(+200ppm), appropriate selection of all of the following
are required for the PLL be able to lock: VCSO center
frequency, input frequency, and divider selections.
Post-PLL Divider
The M1033/34 features a post-PLL (P) divider. By using
the P Divider, the device’s output frequency (Fout) can
be the VCSO center frequency (Fvcso) or 1/2 Fvcso.
The P_SEL pin selects the value for the P divider: logic 1
sets P to 2, logic 0 sets P to 1. (See Table 5 on pg. 4.)
When the P divider is included, the complete relation-
ship for the output frequency (Fout) is defined as:
Due to the narrow tuning range of the VCSO
(+200ppm), appropriate selection of all of the following
are required for the PLL be able to lock: VCSO center
frequency, input frequency, and divider selections.
MUX
0
REF_SEL
1
VCC
50k
VCC
50k
LVCMOS/
LVTTL
LVPECL
50k
VCC
82
127
VCC
82
127
M1025/26
X
DIF_REF0
nDIF_REF0
DIF_REF1
nDIF_REF1
Fvcso
Fin
M
R
----
×
=
Fout
Fvcso
P
-------------------
=
Fin
M
RP
×
------------------
×
=
相关PDF资料 |
PDF描述 |
|---|---|
| M200PXXX.XXXX-040K | SPECIALTY LOGIC CIRCUIT, MDIP24 |
| M200PXXX.XXXX-046K | SPECIALTY LOGIC CIRCUIT, MDIP24 |
| M200PXXX.XXXX-050M | SPECIALTY LOGIC CIRCUIT, MDIP24 |
| M200PXXX.XXXX-053K | SPECIALTY LOGIC CIRCUIT, MDIP24 |
| M200PXXX.XXXX-196L | SPECIALTY LOGIC CIRCUIT, MDIP24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M-103-427 | 制造商:Brady Corporation 功能描述:WIRE MARKER SELF LAM 1"W X 1 制造商:Brady Corporation 功能描述:WIRE MARKER, SELF LAM, 1"W X 1.25"H, 200 制造商:Brady Corporation 功能描述:WIRE MARKER, SELF LAM, 1"W X 1.25"H, 200/ROLL; Marker Type:Self Laminating; Marker Dimensions:12.7mm x 25.4mm; Marker Material:Vinyl; Legend:Blank (No Legend); Legend Color:Black; Marker Color:White; Label Size:1"W x 0.5"H; Series:M ;RoHS Compliant: Yes |
| M-103-498 | 制造商:Brady Corporation 功能描述:LAB ID LABEL, VINYL CLOTH, 1"W X 1.25"H, 160/ROLL; Label Type:Self Adhesive; Label Material:Vinyl Cloth; Background Color:White; Pack Quantity:160; Accessory Type:M Series Lab ID Labels; Legend:Blank (No Legend); Legend Color:Black ;RoHS Compliant: Yes |
| M1035 HHHTSCZ50- | 制造商:TR FASTENINGS 功能描述:SET SCREW HT BZP M10X35 制造商:TR FASTENINGS 功能描述:SET SCREW, HT, BZP, M10X35 制造商:TR FASTENINGS 功能描述:SET SCREW, HT, BZP, M10X35; Thread Size - Metric:M10; Screw Length:35mm; Fastener Plating:Bright Zinc; Fastener Material:Steel; Screw Head Style:Hex; SVHC:No SVHC (19-Dec-2012); Body Plating:Zinc; Driver Type:Nut; Length:35mm; ;RoHS Compliant: Yes |
| M1035HCZ109 | 制造商:n/a 功能描述:Ships in 2 days |
| M1035SFA10 | 制造商:n/a 功能描述:Ships in 2 days |
发布紧急采购，3分钟左右您将得到回复。