参数资料
型号: M25P16-VMN6G
厂商: 意法半导体
元件分类: DRAM
英文描述: 4 Mbit Uniform Sector, Serial Flash Memory
中文描述: 4兆位统一部门,串行闪存
文件页数: 28/55页
文件大小: 335K
代理商: M25P16-VMN6G
Instructions
M25P16
28/55
6.8
Page Program (PP)
The Page Program (PP) instruction allows bytes to be programmed in the memory
(changing bits from 1 to 0). Before it can be accepted, a Write Enable (WREN) instruction
must previously have been executed. After the Write Enable (WREN) instruction has been
decoded, the device sets the Write Enable Latch (WEL).
The Page Program (PP) instruction is entered by driving Chip Select (S) Low, followed by
the instruction code, three address bytes and at least one data byte on Serial Data Input (D).
If the 8 least significant address bits (A7-A0) are not all zero, all transmitted data that goes
beyond the end of the current page are programmed from the start address of the same
page (from the address whose 8 least significant bits (A7-A0) are all zero). Chip Select (S)
must be driven Low for the entire duration of the sequence.
The instruction sequence is shown in
Figure 15
.
If more than 256 bytes are sent to the device, previously latched data are discarded and the
last 256 data bytes are guaranteed to be programmed correctly within the same page. If less
than 256 Data bytes are sent to device, they are correctly programmed at the requested
addresses without having any effects on the other bytes of the same page.
For optimized timings, it is recommended to use the Page Program (PP) instruction to
program all consecutive targeted Bytes in a single sequence versus using several Page
Program (PP) sequences with each containing only a few Bytes (see
Table 15: AC
characteristics (Grade 6)
).
Chip Select (S) must be driven High after the eighth bit of the last data byte has been
latched in, otherwise the Page Program (PP) instruction is not executed.
As soon as Chip Select (S) is driven High, the self-timed Page Program cycle (whose
duration is t
PP
) is initiated. While the Page Program cycle is in progress, the Status Register
may be read to check the value of the Write In Progress (WIP) bit. The Write In Progress
(WIP) bit is 1 during the self-timed Page Program cycle, and is 0 when it is completed. At
some unspecified time before the cycle is completed, the Write Enable Latch (WEL) bit is
reset.
A Page Program (PP) instruction applied to a page which is protected by the Block Protect
(BP2, BP1, BP0) bits (see
Table 2
and
Table 3
) is not executed.
相关PDF资料
PDF描述
M25P16-VMN6P 4 Mbit Uniform Sector, Serial Flash Memory
M25P16-VMN6TG 4 Mbit Uniform Sector, Serial Flash Memory
M25P16-VMP3G 4 Mbit Uniform Sector, Serial Flash Memory
M25P16-VMP3P 4 Mbit Uniform Sector, Serial Flash Memory
M25P16-VMP3TG 4 Mbit Uniform Sector, Serial Flash Memory
相关代理商/技术参数
参数描述
M25P16VMN6P 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:512 Kbit to 32 Mbit, Low Voltage, Serial Flash Memory With 40 MHz or 50 MHz SPI Bus Interface
M25P16-VMN6P 功能描述:闪存 16MBIT SFLASH MEM RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
M25P16-VMN6P/ALT 制造商:Micron Technology Inc 功能描述:16 MBIT, SERIAL FLASH MEMORY, 75 MHZ SPI BUS INTERFACE - Trays
M25P16-VMN6PBA 制造商:Micron Technology Inc 功能描述:NOR Flash Serial-SPI 3.3V 16Mbit 2M x 8bit 15ns 8-Pin SO N Tray 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE - Trays 制造商:Micron Technology Inc 功能描述:IC FLASH 16MX1 PBF SOIC 3.0V
M25P16VMN6T 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:512 Kbit to 32 Mbit, Low Voltage, Serial Flash Memory With 40 MHz or 50 MHz SPI Bus Interface