- 您现在的位置：买卖IC网 > PDF目录358977 > M27C1001-60N6X (意法半导体) 1 Mbit 128Kb x8 UV EPROM and OTP EPROM PDF资料下载
参数资料
| 型号： | M27C1001-60N6X |
| 厂商： | 意法半导体 |
| 英文描述： | 1 Mbit 128Kb x8 UV EPROM and OTP EPROM |
| 中文描述： | 1兆位存储器的128KB x8紫外线和OTP存储器 |
| 文件页数： | 9/17页 |
| 文件大小： | 159K |
| 代理商： | M27C1001-60N6X |
9/17
M27C1001
Electronic Signature
The Electronic Signature (ES) mode allows the
reading out of a binary code from an EPROM that
will identify its manufacturer and type. This mode
is intended for use by programming equipment to
automatically match the device to be programmed
with its corresponding programming algorithm.
The ES mode is functional in the 25°C ± 5°C am-
bient temperature range that is required when pro-
gramming the M27C1001. To activate the ES
mode, the programming equipment must force
11.5V to 12.5V on address line A9 of the
M27C1001, with V
PP
= V
CC
= 5V. Two identifier
bytes may then be sequenced from the device out-
puts by toggling address line A0 from V
IL
to V
IH
. All
other address lines must be held at V
IL
during
Electronic Signature mode.
Byte 0 (A0 = V
IL
) represents the manufacturer
code and byte 1 (A0 = V
IH
) the device identifier
code. For the STMicroelectronics M27C1001,
these two identifier bytes are given in Table 4 and
can be read-out on outputs Q7 to Q0.
ERASURE OPERATION (applies to UV EPROM)
The erasure characteristics of the M27C1001 is
such that erasure begins when the cells are ex-
posed to light with wavelengths shorter than ap-
proximately 4000 . It should be noted that
sunlight and some type of fluorescent lamps have
wavelengths in the 3000-4000 range. Research
shows that constant exposure to room level fluo-
rescent lighting could erase a typical M27C1001 in
about 3 years, while it would take approximately 1
week to cause erasure when exposed to direct
sunlight. If the M27C1001 is to be exposed to
these types of lighting conditions for extended pe-
riods of time, it is suggested that opaque labels be
put over the M27C1001 window to prevent unin-
tentional erasure. The recommended erasure pro-
cedure for the M27C1001 is exposure to short
wave ultraviolet light which has a wavelength of
2537 . The integrated dose (i.e. UV intensity x
exposure time) for erasure should be a minimum
of 15 W-sec/cm
2
. The erasure time with this dos-
age is approximately 15 to 20 minutes using an ul-
traviolet lamp with 12000 μW/cm
2
power rating.
The M27C1001 should be placed within 2.5 cm (1
inch) of the lamp tubes during the erasure. Some
lamps have a filter on their tubes which should be
removed before erasure.
相关PDF资料 |
PDF描述 |
|---|---|
| M27C1001-45N6X | 1 Mbit 128Kb x8 UV EPROM and OTP EPROM |
| M27C1001-35N6X | 1 Mbit 128Kb x8 UV EPROM and OTP EPROM |
| M27C1001-90XF1TR | 1 Mbit 128Kb x8 UV EPROM and OTP EPROM |
| M27C1001-90XB6X | 1 Mbit 128Kb x8 UV EPROM and OTP EPROM |
| M27C1001-90XB6TR | 1 Mbit 128Kb x8 UV EPROM and OTP EPROM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M27C1001-60NTR | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:1 Mbit (128 Kbit x 8) UV EPROM and OTP EPROM |
| M27C1001-60XB1TR | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:1 Mbit 128Kb x8 UV EPROM and OTP EPROM |
| M27C1001-60XB1X | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:1 Mbit 128Kb x8 UV EPROM and OTP EPROM |
| M27C1001-60XB3TR | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:1 Mbit 128Kb x8 UV EPROM and OTP EPROM |
| M27C1001-60XB3X | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:1 Mbit 128Kb x8 UV EPROM and OTP EPROM |
发布紧急采购，3分钟左右您将得到回复。