- 您现在的位置：买卖IC网 > PDF目录359020 > M28W800C-ZBT (意法半导体) 8 Mbit 512Kb x16, Boot Block 3V Supply Flash Memory PDF资料下载
参数资料
| 型号： | M28W800C-ZBT |
| 厂商： | 意法半导体 |
| 英文描述： | 8 Mbit 512Kb x16, Boot Block 3V Supply Flash Memory |
| 中文描述： | 8兆位512KB的x16插槽，启动块3V电源快闪记忆体 |
| 文件页数： | 13/49页 |
| 文件大小： | 369K |
| 代理商： | M28W800C-ZBT |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页
13/49
M28W800CT, M28W800CB
Register and/or the Security Block is not revers-
ible.
The Protection Register Program cannot be sus-
pended. See Appendix C, Figure 23, Protection
Register Program Flowchart and Pseudo Code,
for the flowchart for using the Protection Register
Program command.
Block Lock Command
The Block Lock command is used to lock a block
and prevent Program or Erase operations from
changing the data in it. All blocks are locked at
power-up or reset.
Two Bus Write cycles are required to issue the
Block Lock command.
I
The first bus cycle sets up the Block Lock
command.
I
The second Bus Write cycle latches the block
address.
The lock status can be monitored for each block
using the Read Electronic Signature command.
Table. 9 shows the protection status after issuing
a Block Lock command.
The Block Lock bits are volatile, once set they re-
main set until a hardware reset or power-down/
power-up. They are cleared by a Blocks Unlock
command. Refer to the section, Block Locking, for
a detailed explanation.
Block Unlock Command
The Blocks Unlock command is used to unlock a
block, allowing the block to be programmed or
erased. Two Bus Write cycles are required to is-
sue the Blocks Unlock command.
I
The first bus cycle sets up the Block Unlock
command.
I
The second Bus Write cycle latches the block
address.
The lock status can be monitored for each block
using the Read Electronic Signature command.
Table. 9 shows the protection status after issuing
a Block Unlock command. Refer to the section,
Block Locking, for a detailed explanation.
Block Lock-Down Command
A locked block cannot be Programmed or Erased,
or have its protection status changed when WP is
low, V
IL
. When WP is high, V
IH,
the Lock-Down
function is disabled and the locked blocks can be
individually unlocked by the Block Unlock com-
mand.
Two Bus Write cycles are required to issue the
Block Lock-Down command.
I
The first bus cycle sets up the Block Lock
command.
I
The second Bus Write cycle latches the block
address.
The lock status can be monitored for each block
using the Read Electronic Signature command.
Locked-Down blocks revert to the locked (and not
locked-down) state when the device is reset on
power-down. Table. 9 shows the protection status
after issuing a Block Lock-Down command. Refer
to the section, Block Locking, for a detailed expla-
nation.
相关PDF资料 |
PDF描述 |
|---|---|
| M28W800CT90N1T | 8 Mbit 512Kb x16, Boot Block 3V Supply Flash Memory |
| M28W800CB70N6T | 8 Mbit 512Kb x16, Boot Block 3V Supply Flash Memory |
| M28W800CB70N1T | 8 Mbit 512Kb x16, Boot Block 3V Supply Flash Memory |
| M28W800CB90ZB1T | Dual 2-Input Positive-NAND Gate 8-SO 0 to 70 |
| M28W800CB90N6T | 8 Mbit 512Kb x16, Boot Block 3V Supply Flash Memory |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M2901-155.52MHZ | 制造商:MF Electronics 功能描述: |
| M29016B70N1 | 制造商:STMicroelectronics 功能描述: |
| M2901LC | 制造商:Motorola Inc 功能描述: 制造商:MOTOROLA 功能描述: |
| M2904 | 制造商:UTC-IC 制造商全称:UTC-IC 功能描述:LINEAR INTEGRATED CIRCUIT |
| M2904_10 | 制造商:UTC-IC 制造商全称:UTC-IC 功能描述:SINGLE-SUPPLY DUAL OPERATIONAL AMPLIFIER |
发布紧急采购，3分钟左右您将得到回复。