- 您现在的位置：买卖IC网 > PDF目录359020 > M29DW128F60NF6F (意法半导体) 128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V Supply, Flash Memory PDF资料下载
参数资料
| 型号： | M29DW128F60NF6F |
| 厂商： | 意法半导体 |
| 英文描述： | 128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V Supply, Flash Memory |
| 中文描述： | 128兆位（16Mb的x8或和8Mb x16插槽，多行，页，引导块）3V电源，快闪记忆体 |
| 文件页数： | 15/93页 |
| 文件大小： | 719K |
| 代理商： | M29DW128F60NF6F |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页
M29DW128F
2 Signal descriptions
15/93
2.7
Write Enable (W)
The Write Enable pin, W, controls the Bus Write operation of the memory’s Command Interface.
2.8
V
PP/
Write Protect (V
PP
/WP)
The V
PP
/Write Protect
pin provides two functions. The V
PP
function allows the memory to use
an external high voltage power supply to reduce the time required for Program operations. This
is achieved by bypassing the unlock cycles and/or using the multiple Word (2 or 4 at-a-time) or
multiple Byte Program (2, 4 or 8 at-a-time) commands.
The Write Protect function provides a hardware method of protecting the four outermost boot
blocks (two at the top, and two at the bottom of the address space). When V
PP
/Write Protect is
Low, V
IL
, the memory protects the four outermost boot blocks; Program and Erase operations in
these blocks are ignored while V
PP
/Write Protect is Low, even when RP is at V
ID
.
When V
PP
/Write Protect
is High, V
IH
, the memory reverts to the previous protection status of
the four outermost boot blocks. Program and Erase operations can now modify the data in
these blocks unless the blocks are protected using Block Protection.
Applying V
PPH
to the V
PP
/WP pin will temporarily unprotect any block previously protected
(including the four outermost parameter blocks) using a High Voltage Block Protection
technique (In-System or Programmer technique). See
Table 9: Hardware Protection
for details.
When V
PP
/Write Protect is raised to V
PP
the memory automatically enters the Unlock Bypass
mode. When V
PP
/Write Protect returns to V
IH
or V
IL
normal operation resumes. During Unlock
Bypass Program operations the memory draws I
PP
from the pin to supply the programming
circuits. See the description of the Unlock Bypass command in the Command Interface section.
The transitions from V
IH
to V
PP
and from V
PP
to V
IH
must be slower than t
VHVPP
, see
Figure 20
.
Never raise V
PP
/Write Protect to V
PP
from any mode except Read mode, otherwise the
memory may be left in an indeterminate state.
The V
PP
/Write Protect pin must not be left floating or unconnected or the device may become
unreliable. A 0.1μF capacitor should be connected between the V
PP
/Write Protect pin and the
V
SS
Ground pin to decouple the current surges from the power supply. The PCB track widths
must be sufficient to carry the currents required during Unlock Bypass Program, I
PP
.
2.9
Reset/Block Temporary Unprotect (RP)
The Reset/Block Temporary Unprotect pin can be used to apply a Hardware Reset to the
memory or to temporarily unprotect all the blocks previously protected using a High Voltage
Block Protection technique (In-System or Programmer technique).
Note that if V
PP
/WP is at V
IL
, then the four outermost parameter blocks will remain protected
even if RP is at V
ID
.
A Hardware Reset is achieved by holding Reset/Block Temporary Unprotect Low, V
IL
, for at
least t
PLPX
. After Reset/Block Temporary Unprotect goes High, V
IH
, the memory will be ready
for Bus Read and Bus Write operations after t
PHEL
or t
RHEL
, whichever occurs last. See the
Ready/Busy Output section,
Table 30: Reset/Block Temporary Unprotect AC Characteristics
and
Figure 18
and
Figure 19
for more details.
相关PDF资料 |
PDF描述 |
|---|---|
| M29DW128F60NF6T | 128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V Supply, Flash Memory |
| M29DW128F60ZA1 | 128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V Supply, Flash Memory |
| M29DW128F60ZA1E | 128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V Supply, Flash Memory |
| M29DW128F60ZA1F | 128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V Supply, Flash Memory |
| M29DW128F60ZA1T | 128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V Supply, Flash Memory |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M29DW128F60NF6T | 制造商:NUMONYX 制造商全称:Numonyx B.V 功能描述:128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V supply Flash memory |
| M29DW128F60ZA1 | 制造商:STMICROELECTRONICS 制造商全称:STMicroelectronics 功能描述:128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V supply Flash memory |
| M29DW128F60ZA1E | 制造商:NUMONYX 制造商全称:Numonyx B.V 功能描述:128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V supply Flash memory |
| M29DW128F60ZA1F | 制造商:NUMONYX 制造商全称:Numonyx B.V 功能描述:128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V supply Flash memory |
| M29DW128F60ZA1T | 制造商:NUMONYX 制造商全称:Numonyx B.V 功能描述:128 Mbit (16Mb x8 or 8Mb x16, Multiple Bank, Page, Boot Block) 3V supply Flash memory |
发布紧急采购，3分钟左右您将得到回复。