- 您现在的位置：买卖IC网 > PDF目录80580 > M30622M8T-XXXFP 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 PDF资料下载
参数资料
| 型号： | M30622M8T-XXXFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 |
| 封装： | PLASTIC, QFP-100 |
| 文件页数： | 13/188页 |
| 文件大小： | 3064K |
| 代理商： | M30622M8T-XXXFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页第130页第131页第132页第133页第134页第135页第136页第137页第138页第139页第140页第141页第142页第143页第144页第145页第146页第147页第148页第149页第150页第151页第152页第153页第154页第155页第156页第157页第158页第159页第160页第161页第162页第163页第164页第165页第166页第167页第168页第169页第170页第171页第172页第173页第174页第175页第176页第177页第178页第179页第180页第181页第182页第183页第184页第185页第186页第187页第188页
Mitsubishi microcomputers
M16C / 62T Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
10
Pin Description
Pin Description
Pin name
P40 to P47
______
CS0 to CS3,
A16 to A19
P50 to P57
________ ______
WRL/WR,
_________ _______
WRH/BHE,
RD,
BCLK,
__________
HLDA,
__________
HOLD,
ALE,
________
RDY
P60 to P67
P70 to P77
P80 to P84,
P86,
P87,
P85
P90 to P97
P100 to P107
Signal name
I/O port P4
I/O port P5
I/O port P6
I/O port P7
I/O port P8
I/O port P85
I/O port P9
I/O port P10
I/O type
Input/output
Output
Input/output
Output
Input
Output
Input
Input/output
Input
Input/output
Function
This is an 8-bit I/O port equivalent to P0.
______
_______
These pins output CS0–CS3 signals and A16–A19. CS0–CS3 are
chip select signals used to specify an access space. A16–A19 are 4
high-order address bits.
This is an 8-bit I/O port equivalent to P0. In single-chip mode, P57 in
this port outputs a divide-by-8 or divide-by-32 clock of XIN or a clock
of the same frequency as XCIN as selected by software.
________
______
_______
_____
__________
Output WRL, WRH (WR and BHE), RD, BCLK, HLDA, and ALE
________
_________
_______
______
signals. WRL and WRH, and BHE and WR can be switched using
software control.
________
_____
s WRL, WRH, and RD selected
With a 16-bit external data bus, data is written to even addresses
________
when the WRL signal is “L” and to the odd addresses when the
________
_____
WRH signal is “L”. Data is read when RD is “L”.
______
_______
_____
s WR, BHE, and RD selected
______
_____
Data is written when WR is “L”. Data is read when RD is “L”. Odd
_______
addresses are accessed when BHE is “L”. Use this mode when
using an 8-bit external data bus.
__________
While the input level at the HOLD pin is “L”, the microcomputer is
__________
placed in the hold state. While in the hold state, HLDA outputs a
“L” level. ALE is used to latch the address. While the input level of
_______
the RDY pin is “L”, the microcomputer is in the ready state.
This is an 8-bit I/O port equivalent to P0. When used for input in
single-chip, memory expansion, and microprocessor modes, the
port can be set to have or not have a pull-up resistor in units of four
bits by software. Pins in this port also function as UART0 and
UART1 I/O pins as selected by software.
This is an 8-bit I/O port equivalent to P6 (P70 and P71 are N channel
open-drain output). Pins in this port also function as timer A0–A3,
timer B5 or UART2 I/O pins as selected by software.
P80 to P84, P86 and P87 are I/O ports with the same functions as P6.
Using software, they can be made to function as the I/O pins for
timer A4 and the input pins for external interrupts. P86 and P87 can
be set using software to function as the I/O pins for a sub clock
generation circuit. In this case, connect a quartz oscillator between
P86 (XCOUT pin) and P87 (XCIN pin). P85 is an input-only port that
_______
also functions for NMI. The NMI interrupt is generated when the
_______
input at this pin changes from “H” to “L”. The NMI function cannot be
cancelled using software. The pull-up cannot be set for this pin.
This is an 8-bit I/O port equivalent to P6. Pins in this port also
function as SI/O 3, 4 I/O pins, timer B0–B4 input pins, D-A converter
output pins, A-D converter extended input pins, or A-D trigger input
pins as selected by software.
This is an 8-bit I/O port equivalent to P6. Pins in this port also
funciton as A-D converter input pins. Furthermore, P104–P107 also
function as input pins for the key input interrupt function.
Note 1: In M30623(80-pin package), the following signals do not have the corresponding external pin.
_______
q P10/D8 to P14/D12, P15/D13/INT3 to P17/D15/INT5
_______
q P44/CS0 to P47/CS3
________
__
___
q P72/CLK2/TA1OUT/V, P73/CST2/RTS2/TA1IN/V, P74/TA2OUT/W, P75/TA2IN/W
q P91/TB1IN/SIN3
Note 2: The M16C/62T group is not guaranteed to operate in memory expansion and microprocessor modes.
相关PDF资料 |
PDF描述 |
|---|---|
| M38004E8FS | 8-BIT, UVPROM, 8 MHz, MICROCONTROLLER, CQCC64 |
| M34507M4-XXXFP | 4-BIT, MROM, MICROCONTROLLER, PDSO24 |
| M37754M8C-XXXHP | 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP100 |
| M38514E6SP | 8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PDIP42 |
| M37477M8-XXXFP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PDSO32 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M30622M8-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:16-BIT SINGLE-CHIP MICROCOMPUTER M16C FAMILY |
| M30622M8-XXXFS | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:16-BIT SINGLE-CHIP MICROCOMPUTER M16C FAMILY |
| M30622M8-XXXGP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:16-BIT SINGLE-CHIP MICROCOMPUTER M16C FAMILY |
| M30622MA-173FP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M30622MA-179GP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。