- 您现在的位置：买卖IC网 > PDF目录80536 > M34513E4FP 4-BIT, OTPROM, 4.2 MHz, MICROCONTROLLER, PQFP32 PDF资料下载
参数资料
| 型号： | M34513E4FP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 4-BIT, OTPROM, 4.2 MHz, MICROCONTROLLER, PQFP32 |
| 封装： | 7 X 7 MM, 0.80 MM PITCH, PLASTIC, LQFP-32 |
| 文件页数： | 32/96页 |
| 文件大小： | 1078K |
| 代理商： | M34513E4FP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页当前第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页
38
4513/4514 Group
SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
Table 13 Processing sequence of data transfer from master to slave
1-byte data is serially transferred on this process. Subsequently, data
can be transferred continuously by repeating the process from *.
When an external clock is selected as a synchronous clock, the
clock is not controlled internally. Control the clock externally be-
cause serial transfer is performed as long as clock is externally
input. (Unlike an internal clock, an external clock is not stopped
when serial transfer is completed.) However, the SIOF flag is set to
“1” when the clock is counted 8 times after executing the SST in-
struction. Be sure to set the initial level of the external clock to “H.”
Master (transmission)
[Initial setting]
Setting the serial I/O mode register J1 and inter-
rupt control register V2 shown in Figure 24.
TJ1A and TV2A instructions
Setting the port received the reception enable
signal (SRDY) to the input mode.
(Port D5 is used in this example)
SD instruction
* [Transmission enable state]
Storing transmission data to serial I/O register SI.
TSIAB instruction
[Transmission]
Check port D5 is “L” level.
SZD instruction
Serial transfer starts.
SST instruction
Check transmission completes.
SNZSI instruction
Wait (timing when continuously transferring)
Slave (reception)
[Initial setting]
Setting serial I/O mode register J1, and interrupt control register V2 shown in
Figure 24.
TJ1A and TV2A instructions
Setting the port transmitted the reception enable signal (SRDY) and outputting
“H” level (reception impossible).
(Port D5 is used in this example)
SD instruction
*[Reception enable state]
The SIOF flag is cleared to “0.”
SST instruction
“L” level (reception possible) is output from port D5.
RD instruction
[Reception]
Check reception completes.
SNZSI instruction
“H” level is output from port D5.
SD instruction
[Data processing]
相关PDF资料 |
PDF描述 |
|---|---|
| MC68HC05J5ADWR2 | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO20 |
| MC68HC05K1VDWR3 | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PDSO16 |
| MSU2958C25-006Q | 8-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP44 |
| MSU2958C25-010U | 8-BIT, FLASH, 25 MHz, MICROCONTROLLER, PQFP44 |
| MSU2958C16-011U | 8-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP44 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M34513E4SP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34513E8 | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34513E8FP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34513M2 | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34513M2-420FP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。