- 您现在的位置：买卖IC网 > PDF目录67761 > M34519M6-XXXFP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO42 PDF资料下载
参数资料
| 型号： | M34519M6-XXXFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO42 |
| 封装： | 0.450 INCH, 0.80 MM PITCH, PLASTIC, SSOP-42 |
| 文件页数： | 16/50页 |
| 文件大小： | 1808K |
| 代理商： | M34519M6-XXXFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页当前第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页
23
9571B–AT42–08/10
AT42QT1111-MU/AT42QT1111-AU
5.4
Reset (0x04)
The Reset command forces the QT1111 to reset. If the setups data is present in the EEPROM,
the setups are loaded into the device. Otherwise default settings are applied.
The host must wait for at least 320 ms for the operation to be completed before communications
can be re-established.
5.5
Sleep (0x05)
The Sleep command puts the device into sleep mode (see Section 4.3 on page 17).
The host must wait for at least 300 s after a low signal is applied to the SS or CHANGE pin to
wake the device before communications can be re-established.
5.6
Store to EEPROM (0x0A)
Stores the current RAM contents to the QT1111’s internal EEPROM. When the device is reset, it
will automatically reload these settings.
The host must wait for at least 200 ms for the operation to be completed before communications
can be re-established.
5.7
Restore from EEPROM (0x0B)
Settings stored in EEPROM are automatically loaded into RAM when the device is reset. If
desired, these settings can be re-loaded into RAM using the “Restore from EEPROM”
command.
The host must wait for at least 150 ms for the operation to be completed before communications
can be re-established.
5.8
Erase EEPROM (0x0C)
This command erases the settings stored in EEPROM and then resets the QT1111. This causes
the QT1111 to revert to its default settings.
The host must wait for at least 50 ms for the operation to be completed before communications
can be re-established.
Note that under the default settings, the CRC is disabled. By erasing the EEPROM, therefore,
the default settings are restored and the QT1111 is put into non-CRC mode regardless of the
previous setting.
5.9
Recover EEPROM (0x0D)
This command “undeletes” the setup data that was previously stored in the device’s EEPROM
and has been erased using the “Erase EEPROM” command.
Note:
If valid settings have not previously been stored in the device EEPROM, the QT1111
continues to operate under the default settings.
The host must wait for at least 50 ms for the operation to be completed before communications
can be re-established.
相关PDF资料 |
PDF描述 |
|---|---|
| M34519M8-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO42 |
| M34519E8FP | 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO42 |
| M34519M8-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO42 |
| M34519M6-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PDSO42 |
| M34553M8H-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP48 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M34519M8-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:4-BIT CISC SINGLE-CHIP MICROCOMPUTER 720 FAMILY / 4500 SERIES |
| M34-52 | 制造商:GAMEWELL-FCI 制造商全称:GAMEWELL-FCI 功能描述:Three-Fold Fire Alarm Boxes and Transmitters |
| M34524EDFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34524M8-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
| M34524MC-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:4-BIT CISC SINGLE-CHIP MICROCOMPUTER 720 FAMILY / 4500 SERIES |
发布紧急采购，3分钟左右您将得到回复。