- 您现在的位置：买卖IC网 > PDF目录132962 > M37207EFFP 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP80 PDF资料下载
参数资料
| 型号： | M37207EFFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP80 |
| 封装： | 14 X 20 MM, 0.80 MM PITCH, PLASTIC, QFP-80 |
| 文件页数： | 96/121页 |
| 文件大小： | 1907K |
| 代理商： | M37207EFFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页当前第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页
MITSUBISHI MICROCOMPUTERS
M37207MF-XXXSP/FP, M37207M8-XXXSP
M37207EFSP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
and ON-SCREEN DISPLAY CONTROLLER
76
Fig. 76. Ceramic Resonator Circuit Example
Fig. 77. External Clock Input Circuit Example
(3) Low-Speed Mode
If the internal clock is generated from the sub-clock (XCIN), a low
power consumption operation can be realized by stopping only the
main clock XIN. To stop the main clock, set bit 6 (CM6) of the CPU
mode register (00FB16) to “1.” When the main clock XIN is restarted,
the program must allow enough time to for oscillation to stabilize.
Note that in low-power-consumption mode the XCIN-XCOUT drivability
can be reduced, allowing even lower power consumption (20
A with
f (XCIN) = 32kHz). To reduce the XCIN-XCOUT drivability, clear bit 5
(CM5) of the CPU mode register (00FB16) to “0.” At reset, this bit is
set to “1” and strong drivability is selected to help the oscillation to
start. When an STP instruction is executed, set this bit to “1” by soft-
ware before executing.
CLOCK GENERATING CIRCUIT
This microcomputer has 2 built-in oscillation circuits. An oscillation
circuit can be formed by connecting a resonator between XIN and
XOUT (XCIN and XCOUT). Use the circuit constants in accordance with
the resonator manufacturer’s recommended values. No external re-
sistor is needed between XIN and XOUT since a feed-back resistor
exists on-chip. However, an external feed-back resistor is needed
between XCIN and XCOUT. When using XCIN-XCOUT as sub-clock,
clear bits 7 and 6 of the mixing control register to “0.” To supply a
clock signal externally, input it to the XIN (XCIN) pin and make the
XOUT (XCOUT) pin open. When not using XCIN clock, connect the
XCIN to VSS and make the XCOUT pin open.
After reset has completed, the internal clock
φ is half the frequency of
XIN. Immediately after poweron, both the XIN and XCIN clock start
oscillating. To set the internal clock
φ to low-speed operation mode,
set bit 7 of the CPU mode register (address 00FB16) to “1.”
Oscillation Control
(1) Stop mode
The built-in clock generating circuit is shown in Figure 78. When the
STP instruction is executed, the internal clock
φ stops at HIGH. At
the same time, timers 3 and 4 are connected by hardware and “FF16”
is set in timer 3 and “0716” is set in the timer 4. Select f(XIN)/16 or
f(XCIN)/16 as the timer 3 count source (set bit 0 of the timer mode
register 2 to “0” before the execution of the STP instruction). More-
over, set the timer 3 and timer 4 interrupt enable bits to disabled (“0”)
before execution of the STP instruction. The oscillator restarts when
external interrupt is accepted. However, the internal clock
φ keeps its
HIGH until timer 4 overflows, allowing time for oscillation stabilization
when a ceramic resonator or a quartz-crystal oscillator is used.
(2) Wait mode
When the WIT instruction is executed, the internal clock
φ stops in
the “H” level but the oscillator continues running. This wait state is
released at reset or when an interrupt is accepted (Note). Since the
oscillator does not stop, the next instruction can be executed at once.
Note: In the wait mode, the following interrupts are invalid.
(1) VSYNC interrupt
(2) CRT interrupt
(3) f(XIN)/4096 interrupt
(4) Timer 1 and 2 interrupts using TIM2 pin input as count
source
(5) Timer 1 interrupt using f(XIN)/4096 or f(XCIN)/4096 as
count source
(6) Timer 3 interrupt using TIM3 pin input as count source
(7) Multi-master I2C-BUS interface interrupt
(8) Timer 4 interrupt using f(XIN)/2 or f(XCIN)/2 as count souce
XCIN
XIN
CCIN
Microcomputer
XCOUT
Rf
Rd
CCOUT
XOUT
CIN
COUT
26
25
30
31
XCIN
Microcomputer
External oscillation
circuit or external
pulse
XCOUT XIN
XOUT
Open
External oscillation
circuit
Vcc
Vss
Vcc
Vss
相关PDF资料 |
PDF描述 |
|---|---|
| M37212M8-XXXSP | 8-BIT, MROM, MICROCONTROLLER, PDIP52 |
| MC68HC05K0CDWR2 | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PDSO16 |
| MC68HC05K0DWR3 | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PDSO16 |
| MC68HC05K0VDWR3 | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PDSO16 |
| M41T11MH | 0 TIMER(S), REAL TIME CLOCK, PDSO28 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M37207EFSP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER and ON-SCREEN DISPLAY CONTROLLER |
| M37207M8 | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER and ON-SCREEN DISPLAY CONTROLLER |
| M37207M8-059SP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER and ON-SCREEN DISPLAY CONTROLLER |
| M37207M8-XXXSP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER and ON-SCREEN DISPLAY CONTROLLER |
| M37207MF | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER and ON-SCREEN DISPLAY CONTROLLER |
发布紧急采购，3分钟左右您将得到回复。