参数资料
型号: M37210E4SP
元件分类: 微控制器/微处理器
英文描述: 8-BIT, OTPROM, 8.1 MHz, MICROCONTROLLER, PDIP52
封装: 0.600 INCH, 1.78 MM PITCH, SHRINK, PLASTIC, DIP-52
文件页数: 38/59页
文件大小: 764K
代理商: M37210E4SP
MITSUBISHI MICROCOMPUTERS
M37210M3-XXXSP/FP, M37210M4-XXXSP, M37211M2-XXXSP
M37210E4-XXXSP/FP, M37210E4SP/FP
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
43
DATA REQUIRED FOR MASK ORDERS
The following are necessary when ordering a mask ROM production.
(1) Mask ROM Order Confirmation Form
(2) Mark Specification Form
(3) Data to be written to ROM, in EPROM form (28-pin DIP type
27256, three identical copies)
PROM Programming Method
The built-in PROM of the blank One Time PROM version and built-in
EPROM version can be read or programmed with a general-purpose
PROM programmer using a special programming adapter.
Product
M37210E4SP
M37210E4FP
Name of Programming Adapter
PCA4754
PCA4756
The PROM of the blank One Time PROM version is not tested
or screened in the assembly process and following processes. To
ensure proper operation after programming, the procedure shown
in Figure 45 is recommended to verify programming.
Fig. 45 Programming and testing of One Time PROM version
Programming with
PROM programmer
Screening (Caution)
(150 for 40 hours)
Verification with
PROM programmer
Functional check in target device
Caution : The screening temperature is far higher than the
storage temperature. Never expose to 150°C ex-
ceeding 100 hours.
PROGRAMMING NOTES
(1) The divide ratio of the timer is 1/ (n + 1).
(2) Even though the BBC and BBS instructions are executed imme-
diately after the interrupt request bits are modified (by the pro-
gram), those instructions are only valid for the contents before
the modification. At least one instruction cycle is needed (such as
an NOP) between the modification of the interrupt request bits
and the execution of the BBC and BBS instructions.
(3) After the ADC and SBC instructions are executed (indecimal op-
eration mode), one instruction cycle (such as an NOP) is needed
before the SEC, CLC, or CLD instructions are executed.
(4) An NOP instruction is needed immediately after the execution of
a PLP instruction.
(5) In order to avoid noise and latch-up, connect a bypass capacitor
(
≈ 0.1F) directly between the VCC pin and VSS pin using a thick
wire.
相关PDF资料
PDF描述
M37210M3-XXXFP 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PQFP64
M37211M2-XXXSP 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP52
M37210E4-XXXSP 8-BIT, OTPROM, 8.1 MHz, MICROCONTROLLER, PDIP52
M37212EFFP 8-BIT, OTPROM, MICROCONTROLLER, PQFP80
M37212M4-XXXSP 8-BIT, MROM, MICROCONTROLLER, PDIP52
相关代理商/技术参数
参数描述
M37210E4-XXXFP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37210E4-XXXSP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37210M3 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37210M3-010SP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER
M37210M3-506SP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER