- 您现在的位置：买卖IC网 > PDF目录80478 > M37221MAH-XXXSP 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP42 PDF资料下载
参数资料
| 型号： | M37221MAH-XXXSP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP42 |
| 封装： | 0.600 INCH, 1.78 MM PITCH, PLASTIC, SDIP-42 |
| 文件页数： | 48/112页 |
| 文件大小： | 1207K |
| 代理商： | M37221MAH-XXXSP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页当前第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页
40
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER
with ON-SCREEN DISPLAY CONTROLLER
M37221M4H/M6H/M8H/MAH–XXXSP/FP
M37221EASP/FP
MITSUBISHI MICROCOMPUTERS
Rev. 1.0
8.6.8 START/STOP Condition Detect Conditions
The START/STOP condition detect conditions are shown in
Figure 8.6.11 and Table 8.6.3. Only when the 3 conditions of Table
8.6.3 are satisfied, a START/STOP condition can be detected.
Note: When a STOP condition is detected in the slave mode
(MST = 0), an interrupt request signal “IICIRQ” is generated to the
CPU.
Fig. 8.6.11 START Condition/STOP Condition Detect Timing Dia-
gram
Standard Clock Mode
6.5
s (26 cycles) < SCL
release time
3.25
s (13 cycles) < Setup time
3.25
s (13 cycles) < Hold time
High-speed Clock Mode
1.0
s (4 cycles) < SCL
release time
0.5
s (2 cycles) < Setup time
0.5
s (2 cycles) < Hold time
Table 8.6.3 START Condition/STOP Condition Detect Conditions
Note: Absolute time at
φ = 4 MHz. The value in parentheses denotes the num-
ber of
φ cycles.
Hold time
Setup
time
SCL
SDA
(START condition)
SDA
(STOP condition)
SCL release time
Hold time
Setup
time
8.6.9 Address Data Communication
There are two address data communication formats, namely, 7-bit
addressing format and 10-bit addressing format. The respective ad-
dress communication formats are described below.
(1) 7-bit addressing format
To support the 7-bit addressing format, set the 10BIT SAD bit of the
I2C control register (address 00DA16) to “0.” The first 7-bit address
data transmitted from the master is compared with the high-order 7-
bit slave address stored in the I2C address register (address 00D816).
At the time of this comparison, address comparison of the RBW bit of
the I2C address register (address 00D816) is not made. For the data
transmission format when the 7-bit addressing format is selected,
refer to Figure 8.6.12, (1) and (2).
(2) 10-bit addressing format
To support the 10-bit addressing format, set the 10BIT SAD bit of the
I2C control register (address 00DA16) to “1.” An address comparison
is made between the first-byte address data transmitted from the
master and the 7-bit slave address stored in the I2C address register
(address 00D816). At the time of this comparison, an address com-
parison is performed between the RBW bit of the I2C address regis-
____
ter (address 00D816) and the R/W bit, which is the last bit of the
address data transmitted from the master. In the 10-bit addressing
____
mode, the R/W bit not only specifies the direction of communication
for control data but is also processed as an address data bit.
When the first-byte address data matches the slave address, the
AAS bit of the I2C status register (address 00D916) is set to “1.” After
the second-byte address data is stored into the I2C data shift register
(address 00D716), perform an address comparison between the sec-
ond-byte data and the slave address by software. When the address
data of the 2nd byte matches the slave address, set the RBW bit of
the I2C address register (address 00D816) to “1” by software. This
____
processing can match the 7-bit slave address and R/W data, which
are received after a RESTART condition is detected, with the value
of the I2C address register (address 00D816). For the data transmis-
sion format when the 10-bit addressing format is selected, refer to
Figure 8.6.12, (3) and (4).
相关PDF资料 |
PDF描述 |
|---|---|
| MC68EN360ZP25VL | 4 CHANNEL(S), 10M bps, LOCAL AREA NETWORK CONTROLLER, PBGA357 |
| M38003M6-XXXFP | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP64 |
| M37471E8-XXXFP | 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP56 |
| M30620MC-XXXGP | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 |
| M30624FGGP | 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP100 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M37224M3 | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER |
| M37224M3-050SP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER |
| M37224M3-XXXSP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER |
| M37225ECSP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER |
| M37225M6 | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SNGLE-CHIP 8-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER |
发布紧急采购，3分钟左右您将得到回复。