- 您现在的位置：买卖IC网 > PDF目录69014 > M37630E4FP 8-BIT, OTPROM, 10 MHz, MICROCONTROLLER, PQFP44 PDF资料下载
参数资料
| 型号： | M37630E4FP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, OTPROM, 10 MHz, MICROCONTROLLER, PQFP44 |
| 封装： | 0.80 MM PITCH, PLASTIC, QFP-44 |
| 文件页数： | 15/48页 |
| 文件大小： | 563K |
| 代理商： | M37630E4FP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页当前第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页
MITSUBISHI
ELECTRIC
22
MITSUBISHI MICROCOMPUTERS
7630 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Fig. 20
Timer X bi-phase counter mode operation
(3) Event counter mode
This mode is available with timer X and timer Y.
Count source
The count source for timer X is the input signal to the P14/CNTR0
pin and for timer Y the input signal to P15/CNTR1 pin.
Operation
The timer counts down. On a timer underflow, the corresponding
timer interrupt request bit will be set to “1”, the contents of the
corresponding timer latches will be reloaded to the counters and
counting continues. The active edge used for counting can be
selected by the polarity selection bit of the corresponding pin
P14/CNTR0 or P15/CNTR1. These bits are part of TXM (Structure
of Timer X mode register) and TYM (Structure of timer Y mode
register (f is internal system clock)) registers.
(4) Pulse width measurement mode
This mode is available with timer X only.
Count source
The count source is the output of timer X clock divider. The divi-
sion ratio can be selected by the timer Y mode register.
Operation
The timer counts down while the input signal level on
P14/CNTR0 matches the active polarity selected by the CNTR0
polarity selection bit of TXM (Structure of Timer X mode regis-
ter). On a timer underflow, the timer X interrupt request bit will be
set to “1”, the contents of the timer latches are reloaded to the
counters and counting continues. When the input level changes
from active polarity (as selected), the CNTR0 interrupt request bit
will be set to “1.” The measurement result may be obtained by
reading timer X during interrupt service.
(5) Pulse period measurement mode
This mode is available with timer Y only.
Count source
The count source is the output of timer Y clock divider.
Operation
The active edge of input signal to be measured can be selected
by CNTR1 polarity selection bit (Fig. 18). When this bit is set to
“0”, the time between two consecutive falling edges of the signal
input to P15/CNTR1 pin will be measured, when the polarity bit is
set to “1”, the time between two consecutive rising edges will be
measured.
The timer counts down. On detection of an active edge of input
signal, the contents of the TY counters will be transferred to tem-
porary registers assigned to the same addresses as TY. At the
same time, the contents of TY latches will be reloaded to the
counters and counting continues. The active edge of input signal
also causes the CNTR1 interrupt request bit to be set to “1”. The
measurement result may be obtained by reading timer Y during
interrupt service.
(6) H/L pulse width measurement mode
This mode is available with timer Y only.
Count source
The count source is the output of the timer Y’s clock divider.
Operation
This mode measures both the “H” and “L” periods of a signal
input to P15/CNTR1 pin continuously. On detection of any edge
(rising or falling) of input signal to P15/CNTR1 pin, the contents of
timer Y counters are stored to temporary registers which are
assigned to the same addresses as timer Y. At the same time,
the contents of timer Y latches are reloaded to the counters and
counting continues. The detection of an edge causes the
CNTR1 interrupt request bit to be set to “1” as well. The result of
measurement may be obtained by reading timer Y during inter-
rupt service. This read access will address the temporary regis-
ters. On a timer underflow, the timer Y interrupt request bit will
be set to “1”, the contents of timer Y latches will be transferred to
the counters and counting continues.
P13/TX0 input signal
P14/CNTR0 input signal
TX counter
count direction
down
up
相关PDF资料 |
PDF描述 |
|---|---|
| M37640E8FP | 8-BIT, OTPROM, 24 MHz, MICROCONTROLLER, PQFP80 |
| M37640E8FS | 8-BIT, OTPROM, 24 MHz, MICROCONTROLLER, PQFP80 |
| M37640M8-XXXFP | 8-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80 |
| M37640E8FP | 8-BIT, OTPROM, 24 MHz, MICROCONTROLLER, PQFP80 |
| M37643M8-XXXHP | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M37630E4FP#U3 | 功能描述:IC 7630 MCU OTP 44QFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:740/7600 产品培训模块:CAN Basics Part-1 CAN Basics Part-2 Electromagnetic Noise Reduction Techniques Part 1 M16C Product Overview Part 1 M16C Product Overview Part 2 标准包装:1 系列:M16C™ M32C/80/87 核心处理器:M32C/80 芯体尺寸:16/32-位 速度:32MHz 连通性:EBI/EMI，I²C，IEBus，IrDA，SIO，UART/USART 外围设备:DMA，POR，PWM，WDT 输入/输出数:121 程序存储器容量:384KB（384K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:24K x 8 电压 - 电源 (Vcc/Vdd):3 V ~ 5.5 V 数据转换器:A/D 34x10b，D/A 2x8b 振荡器型:内部 工作温度:-20°C ~ 85°C 封装/外壳:144-LQFP 包装:托盘 产品目录页面:749 (CN2011-ZH PDF) 配用:R0K330879S001BE-ND - KIT DEV RSK M32C/87 |
| M37630E4FS | 功能描述:EPROM MCU/8BIT CMOS EMULATION CH RoHS:否 类别:编程器，开发系统 >> 配件 系列:- 标准包装:1 系列:- 附件类型:适配器板 适用于相关产品:RCB230，RCB231，RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE |
| M37630E4T-XXXFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37630E4T-XXXFS | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37630M4T | 制造商:CMLMICRO 制造商全称:CML Microcircuits 功能描述:Baseband Processor for ‘Leisure’ Radios with Data |
发布紧急采购，3分钟左右您将得到回复。