- 您现在的位置：买卖IC网 > PDF目录69014 > M37640E8FP 8-BIT, OTPROM, 24 MHz, MICROCONTROLLER, PQFP80 PDF资料下载
参数资料
| 型号： | M37640E8FP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, OTPROM, 24 MHz, MICROCONTROLLER, PQFP80 |
| 封装： | 14 X 20 MM, 0.80 MM PITCH, PLASTIC, QFP-80 |
| 文件页数： | 3/97页 |
| 文件大小： | 1885K |
| 代理商： | M37640E8FP |
第1页第2页当前第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页
10
Ver 1.4
MITSUBISHI MICROCOMPUTERS
7640 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
1.12.1 Single Chip
In this mode, all ports take on their primary function and
all internal memory is accessible. Those areas that are
not in internal memory are not accessible. Also, slow
memory wait and EDMA are disabled in this mode.
1.12.2 Memory Expansion
In this mode, Ports 0 and 1 output the address bus
(AB0-AB15), port 2 acts as the data bus input and out-
put, and port 3 bits 7 to 3 output RD, WR, SYNC
out, Fout,
and DMA
out, respectively. All memory areas that are not
internal memory or SFR area are accessed externally.
Because ports 0 to 3 lose their normal function in this
mode, the address area for the ports and their direction
registers are treated as external memory. In this mode,
slow memory wait and EDMA can be enabled.
1.12.3 Microprocessor
This mode is primarily the same as memory expansion
mode. The difference is that the internal ROM/EPROM
area can not be accessed and is instead treated as
external memory. Slow memory wait and EDMA can be
enabled in this mode.
1.12.4 Slow Memory Wait
The wait function is used when interfacing with external
memories that are too slow to operate at the normal
read/write speed of the MCU. When this is the case, a
wait can be used to extend the read/write cycle. Three
different wait modes are supported; software wait, RDY
wait, and extended RDY wait. The appropriate mode is
chosen by the setting of bits 0 to 3 of CPMB. The wait
function is disabled for internal memory and is valid only
for memory expansion and microprocessor modes.
Software wait is used to extend the read/write cycle by
one, two, or three cycles of
F. The cycle number is
determined by the value of bits 0 and 1 of CPMB. When
software wait is selected, the value on the RDY pin is
ignored. The timing for software wait is shown in Figure
1.9.
RDY wait is also used to extend the read/write cycle by
one, two, or three cycles
F. In this case, the read/write
cycle is extended if the RDY pin is low when
F
out goes
low (taking into account setup and hold times) at the
beginning of the read/write cycle. The extension time is
fixed by the value of bits 0 and 1 of CPMB and does not
depend on the state of the RDY pin once the read/write
cycle has begun. If the RDY pin is high when
F
out goes
low at the beginning of the read/write cycle, the read/
write cycle is not extended. The timing for RDY wait is
shown in Figure 1.10.
The extended RDY wait mode is used to extend the
read/write cycle by a variable number of cycles of
F.
The exact number is dependent on the state of the RDY
pin and the value of bits 0 and 1 of CPMB. In this mode,
the read/write cycle is extended if the RDY pin is low
when
F
out goes low at the beginning of the read/write
cycle. The read/write cycle continues to be extended
until the RDY pin is high when
F
out goes low, at which
point the read/write cycle completes in one, two, or three
cycles of
F (with respect to the previous low to high
transition of
F), dependent on the value in bits 0 and 1
of CPMB. If the RDY pin is high when
F
out goes low at
the beginning of the read/write cycle, the read/write cycle
is not extended. The timing for this mode is shown in
Figure 1.11.
The wait function can only be enabled for external
memory access in microprocessor or memory expan-
sion modes. However, the wait function can not be en-
abled for accesses to addresses 0008
16 to 000F16 (Port
0 through Port 3 registers) in these modes, even though
the locations are mapped as external memory.
相关PDF资料 |
PDF描述 |
|---|---|
| M37640E8FS | 8-BIT, OTPROM, 24 MHz, MICROCONTROLLER, PQFP80 |
| M37640M8-XXXFP | 8-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80 |
| M37640E8FP | 8-BIT, OTPROM, 24 MHz, MICROCONTROLLER, PQFP80 |
| M37643M8-XXXHP | 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80 |
| M37643F8HP | 8-BIT, FLASH, 12 MHz, MICROCONTROLLER, PQFP80 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M37640E8FS | 功能描述:EPROM MCU/8BIT CMOS EMULATION CH RoHS:否 类别:编程器，开发系统 >> 配件 系列:- 标准包装:1 系列:- 附件类型:适配器板 适用于相关产品:RCB230，RCB231，RCB212 配用:26790D-ND - RCB BREAKOUT BOARD RS232 CABLE |
| M37640M4T | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37640M8-111FP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37640M8-126FP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER |
| M37640M8-XXXFP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE CHIP 8 BIT CMOS MICROCOMPUTER |
发布紧急采购，3分钟左右您将得到回复。