参数资料
型号: M37640M8-XXXFP
元件分类: 微控制器/微处理器
英文描述: 8-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP80
封装: 14 X 20 MM, 0.80 MM PITCH, PLASTIC, QFP-80
文件页数: 10/96页
文件大小: 1477K
代理商: M37640M8-XXXFP
18
Ver 1.4
MITSUBISHI MICROCOMPUTERS
7640 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Direction Register
Pull-up Control
Data Bus
Port Latch
Key-on Wake up Input
1.14.1 I/O Ports
This device has 66 programmable I/O pins arranged
as ports P00 to P87. Each port bit can be configured
as input or output. To set the I/O port bit direction,
write a “1” to the corresponding direction register bit
to select output mode, or write a “0” to the direction
register bit to select input mode.
At reset, all of the direction registers are initialized to
0016, setting all of the I/O ports to input mode.
If data is written to a pin and then read from that pin
while it is in output mode, the data read is the value of
the port latch rather than the value of the pin itself.
Therefore, if an external load changes the value of an
output pin, the intended output value will still be read
correctly. Pins set to input mode are floating (pro-
vided that the pull up resistors are not being used) to
ensure that the value input to such a pin can be read
accurately. In the case when data is written to a pin
configured as an input, the data is written only to the
port latch; the pin itself remains floating.
Most of the I/O Ports are multiplexed with secondary
functions. When a GPI/O is multiplexed with a sec-
ond function, the control signal from the peripheral
overrides the direction register. The multiplexing is
briefly described below. The second function signals
to and from the I/O ports are described in detail in
their respective block’s description.
1.14.1.1 Ports P0, P1, and P3
Ports P0 and P1 act as the address bus (AB0-AB15)
in Microprocessor and Memory Expansion modes.
Bits 0 and 3-7 of Port P3 acts as control signals in
Microprocessor and Memory Expansion modes.
1.14.1.2 Port P2
Port P2 is an 8-bit general purpose I/O port when in
single chip mode. In this mode, the port has key-on
wake up circuitry which can be used to restart the
chip externally from a WIT or STP low power mode.
This port also acts as the data bus during micropro-
cessor and memory expansion modes. Port P2 input
level can be set to reduced VIHL level or CMOS level
by bit 6 of the port control register (PTC).
Fig. 1.15. Ports P0, P1, P2, P3 Block Diagram
Ports P0, P1, P3
Port P2
Direction Register
Data Bus
Port Latch
相关PDF资料
PDF描述
M37640E8FP 8-BIT, OTPROM, 24 MHz, MICROCONTROLLER, PQFP80
M37643M8-XXXHP 8-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP80
M37643F8HP 8-BIT, FLASH, 12 MHz, MICROCONTROLLER, PQFP80
M37700E2AFS 16-BIT, UVPROM, 16 MHz, MICROCONTROLLER, CQCC80
M37700E2AXXXFP 16-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQFP80
相关代理商/技术参数
参数描述
M37641F8E8-XXXFP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37641F8FP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37641F8FP#U0 功能描述:IC 740 MCU FLASH 32K 80QFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:740/7600 标准包装:250 系列:56F8xxx 核心处理器:56800E 芯体尺寸:16-位 速度:60MHz 连通性:CAN,SCI,SPI 外围设备:POR,PWM,温度传感器,WDT 输入/输出数:21 程序存储器容量:40KB(20K x 16) 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:6K x 16 电压 - 电源 (Vcc/Vdd):2.25 V ~ 3.6 V 数据转换器:A/D 6x12b 振荡器型:内部 工作温度:-40°C ~ 125°C 封装/外壳:48-LQFP 包装:托盘 配用:MC56F8323EVME-ND - BOARD EVALUATION MC56F8323
M37641F8HP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37641F8HP#U0 功能描述:IC 740 MCU FLASH 32K 80LQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器, 系列:740/7600 产品培训模块:Graphics LCD System and PIC24 Interface Asynchronous Stimulus 标准包装:27 系列:PIC® 24H 核心处理器:PIC 芯体尺寸:16-位 速度:40 MIP 连通性:I²C,SPI,UART/USART 外围设备:欠压检测/复位,POR,PWM,WDT 输入/输出数:21 程序存储器容量:12KB(4K x 24) 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1K x 8 电压 - 电源 (Vcc/Vdd):3 V ~ 3.6 V 数据转换器:A/D 10x10b/12b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:28-SOIC(0.295",7.50mm 宽) 包装:管件 产品目录页面:648 (CN2011-ZH PDF) 配用:AC164339-ND - MODULE SKT FOR PM3 28SOICDV164033-ND - KIT START EXPLORER 16 MPLAB ICD2