参数资料
型号: M37735EHBXXXFP
元件分类: 微控制器/微处理器
英文描述: 16-BIT, OTPROM, 25 MHz, MICROCONTROLLER, PQFP80
封装: 14 X 20 MM, 0.80 MM PITCH, PLASTIC, QFP-80
文件页数: 2/34页
文件大小: 392K
代理商: M37735EHBXXXFP
10
MITSUBISHI MICROCOMPUTERS
M37735EHBXXXFP
M37735EHBFS
PROM VERSION OF M37735MHBXXXFP
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
FUNCTION IN EPROM MODE
1M mode (equivalent to the M5M27C101K)
Reading
__
To read the EPROM, set the CE and OE pins to a “L” level. Input the
address of the data (A0 – A16) to be read, and the data will be output
to the I/O pins D0 – D7. The data I/O pins will be floating when either
__
the CE or OE pins are in the “H” state.
Programming
Programming must be performed in 8 bits by a byte program. To
__
program to the EPROM, set the CE pin to a “L” level and the OE pin to
a “H” level. The CPU will enter the programming mode when 12.5 V
is applied to the VPP pin. The address to be programmed to is selected
with pins A0 – A16, and the data to be programmed is input to pins D0
___
– D7. Set the PGM pin to a “L” level to being programming.
Erasing
To erase data on this chip, use an ultraviolet light source with a 2537
Angstrom wave length. The minimum radiation power necessary for
erasing is 15 J/cm2.
Programming operation
To program the M37735EHBXXXFP, first set VCC = 6 V, VPP = 12.5
V, and set the address to 0100016. Apply a 0.2 ms programming
pulse, check that the data can be read, and if it cannot be read OK,
repeat the procedure, applying a 0.2 ms programming pulse and
checking that the data can be read until it can be read OK. Record
the accumulated number of pulse applied (X) before the data can be
read OK, and then write the data again, applying a further once this
number of pulses (0.2 ! X ms).
When this series of programming operations is complete, increment
the address, and continue to repeat the procedure above until the
last address has been reached.
Finally, when all addresses have been programmed, read with VCC =
VPP = 5 V (or VCC = VPP = 5.5 V).
Table 2. I/O signal in each mode
Read-out
Output
Disable
Programming
Verify
Program Disable
VIL
VIH
VIL
VIH
VIL
VIH
X
VIH
VIL
VIH
X
VIL
VIH
5 V
12.5 V
5 V
6 V
Output
Floating
Input
Output
Floating
__
CE
__
OE
___
PGM
VPP
VCC
Data I/O
Mode
Pin
Note 1 : An X indicates either VIL or VIH.
Programming operation (equivalent to the M5M27C101K)
AC ELECTRICAL CHARACTERISTICS (Ta = 25 ± 5 °C, VCC = 6 V ± 0.25 V, VPP = 12.5 ± 0.3 V, unless otherwise noted)
Address setup time
__
OE
setup time
Data setup time
Address hold time
Data hold time
Output enable to output float delay
VCC setup time
VPP setup time
___
PGM
pulse width
___
PGM
over program pulse width
__
CE
setup time
__
Data valid from OE
s
ns
s
ms
s
ns
tAS
tOES
tDS
tAH
tDH
tDFP
tVCS
tVPS
tPW
tOPW
tCES
tOE
Min.
2
0
2
0
2
0.19
2
Typ.
0.2
Max.
130
0.21
5.25
150
Symbol
Parameter
Test conditions
Limits
Unit
相关PDF资料
PDF描述
M37735EHLXXXHP 16-BIT, OTPROM, 12 MHz, MICROCONTROLLER, PQFP80
M37736EHLXXXHP 16-BIT, OTPROM, 12 MHz, MICROCONTROLLER, PQFP100
M37736M4BXXXGP 16-BIT, MROM, 25 MHz, MICROCONTROLLER, PQFP100
M37736M4LXXXHP 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP100
M37736MHLXXXHP 16-BIT, MROM, 12 MHz, MICROCONTROLLER, PQFP100
相关代理商/技术参数
参数描述
M37735EHL 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:PROM VERSION OF M37735MHLXXXHP
M37735EHLXXXHP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:PROM VERSION OF M37735MHLXXXHP
M37735M4B 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37735M4BXXXFP 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37735M4L 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER