- 您现在的位置：买卖IC网 > PDF目录69014 > M37753M8C-XXXFP 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP80 PDF资料下载
参数资料
| 型号： | M37753M8C-XXXFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP80 |
| 封装： | PLASTIC, QFP-80 |
| 文件页数： | 2/110页 |
| 文件大小： | 1439K |
| 代理商： | M37753M8C-XXXFP |
第1页当前第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页
9
MITSUBISHI MICROCOMPUTERS
M37753M8C-XXXFP, M37753M8C-XXXHP
M37753S4CFP, M37753S4CHP
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
STACK POINTER (S)
Stack pointer (S) is a 16-bit register. It is used during a subroutine
call or interrupts. It is also used during stack, stack pointer relative,
or stack pointer relative indirect indexed Y addressing mode.
PROGRAM COUNTER (PC)
Program counter (PC) is a 16-bit counter that indicates the low-order
16 bits of the next program memory address to be executed. There
is a bus interface unit between the program memory and the CPU,
so that the program memory is accessed through bus interface unit.
This is described later.
PROGRAM BANK REGISTER (PG)
Program bank register is an 8-bit register that indicates the high-or-
der 8 bits of the next program memory address to be executed. When
a carry occurs by incrementing the contents of the program counter,
the contents of the program bank register (PG) is increased by 1.
Also, when a carry or borrow occurs after adding or subtracting the
offset value to or from the contents of the program counter (PC) us-
ing the branch instruction, the contents of the program bank register
(PG) is increased or decreased by 1, so that programs can be writ-
ten without worrying about bank boundaries.
DATA BANK REGISTER (DT)
Data bank register (DT) is an 8-bit register. With some addressing
modes, the data bank register (DT) is used to specify a part of the
memory address. The contents of data bank register (DT) is used as
the high-order 8 bits of a 24-bit address. Addressing modes that use
the data bank register (DT) are direct indirect, direct indexed X indi-
rect, direct indirect indexed Y, absolute, absolute bit, absolute in-
dexed X, absolute indexed Y, absolute bit relative, and stack pointer
relative indirect indexed Y.
DIRECT PAGE REGISTER (DPR)
Direct page register (DPR) is a 16-bit register. Its contents is used as
the base address of a 256-byte direct page area. The direct page
area is allocated in bank 016, but when the contents of DPR is
FF0116 or greater, the direct page area spans across bank 016 and
bank 116. All direct addressing modes use the contents of the direct
page register (DPR) to generate the data address. If the low-order 8
bits of the direct page register (DPR) is “0016”, the number of cycles
required to generate an address is minimized.
Normally the low-order 8 bits of the direct page register (DPR) is set
to “0016”.
PROCESSOR STATUS REGISTER (PS)
Processor status register (PS) is an 11-bit register. It consists of a
flag to indicate the result of operation and CPU interrupt levels.
Branch operations can be performed by testing the flags C, Z, V, and
N.
The details of each bit of the processor status register are described
below.
1. Carry flag (C)
The carry flag contains the carry or borrow generated by the ALU af-
ter an arithmetic operation. This flag is also affected by shift and ro-
tate instructions. This flag can be set and reset directly with the SEC
and CLC instructions or with the SEP and CLP instructions.
2. Zero flag (Z)
The zero flag is set if the result of an arithmetic operation or data
transfer is zero and reset if it is not. This flag can be set and reset
directly with the SEP and CLP instructions.
3. Interrupt disable flag (I)
When the interrupt disable flag is set to “1”, all interrupts except
___
watchdog timer, DBC, and software interrupt are disabled. This flag
is set to “1” automatically when there is an interrupt. It can be set and
reset directly with the SEI and CLI instructions or SEP and CLP in-
structions.
4. Decimal mode flag (D)
The decimal mode flag determines whether addition and subtraction
are performed as binary or decimal. Binary arithmetic is performed
when this flag is “0”. If it is “1”, decimal arithmetic is performed with
each word treated as 2- or 4- digit decimal. Arithmetic operation is
performed using four digits when the data length flag m is “0” and
with two digits when it is “1”. Decimal adjust is automatically per-
formed. (Decimal operation is possible only with the ADC and SBC
instructions.) This flag can be set and reset with the SEP and CLP
instructions.
相关PDF资料 |
PDF描述 |
|---|---|
| M37753S4CFP | 16-BIT, 40 MHz, MICROCONTROLLER, PQFP80 |
| M37753S4CFP | 16-BIT, 40 MHz, MICROCONTROLLER, PQFP80 |
| M37753M8C-XXXHP | 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP80 |
| M37754M6C-XXXGP | 16-BIT, MROM, 40 MHz, MICROCONTROLLER, PQFP100 |
| M37795STJ | 16-BIT, 8 MHz, MICROCONTROLLER, PQCC84 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M37753M8C-XXXHP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37753S4CFP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37753S4CHP | 制造商:RENESAS 制造商全称:Renesas Technology Corp 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER |
| M37754 | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16BIT CMOS MICROCOMPUTER |
| M37754FFCGP | 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION |
发布紧急采购，3分钟左右您将得到回复。