参数资料
型号: M38002E4FP
元件分类: 微控制器/微处理器
英文描述: 8-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP64
封装: 14 X 14 MM, PLASTIC, QFP-64
文件页数: 27/173页
文件大小: 4203K
代理商: M38002E4FP
3800 GROUP USER’S MANUAL
3-20
APPENDIX
3.3 Notes on use
3.3.4 Notes on input and output pins
(1) Fix of a port input level in stand-by state
Fix input levels of an input and an I/O port for getting effect of low-power dissipation in stand-by state*, especially
for the I/O ports of the N-channel open-drain.
Pull-up (connect the port to VCC) or pull-down (connect the port to VSS) these ports through a resistor.
When determining a resistance value, make sure the following:
qExternal circuit
qVariation of output levels during the ordinary operation
* stand-by state : the stop mode by executing the STP instruction
the wait mode by executing the WIT instruction
Reason
Even when setting as an output port with its direction register, in the following state :
qN-channel......when the content of the port latch is “1”
the transistor becomes the OFF state, which causes the ports to be the high-impedance state. Make sure that the
level becomes “undefined” depending on external circuits.
Accordingly, the potential which is input to the input buffer in a microcomputer is unstable in the state that input
levels of an input and an I/O port are “undefined.” This may cause power source current.
(2) Modify of the content of I/O port latch
When the content of the port latch of an I/O port is modified with the bit managing instruction*, the value of the
unspecified bit may be changed.
Reason
The bit managing instruction is read-modify-write instruction for reading and writing data by a byte unit.
Accordingly, when this instruction is executed on one bit of the port latch of an I/O port, the following is executed
to all bits of the port latch.
qAs for a bit which is set as an input port : The pin state is read in the CPU, and is written to this bit after bit
managing.
qAs for a bit which is set as an output port : The bit value is read in the CPU, and is written to this bit after bit
managing.
Make sure the following :
qEven when a port which is set as an output port is changed for an input port, its port latch holds the output data.
qEven when a bit of a port latch which is set as an input port is not speccified with a bit managing instruction,
its value may be changed in case where content of the pin differs from a content of the port latch.
* bit managing instructions : SEB and CLB instruction
相关PDF资料
PDF描述
M38174E8FP 8-BIT, OTPROM, 6.3 MHz, MICROCONTROLLER, PQFP80
M38254M6DXXXFP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP100
MAF8441P 8-BIT, MROM, 6 MHz, MICROCONTROLLER, PDIP28
M38064E8-XXXFP 8-BIT, OTPROM, MICROCONTROLLER, PQFP80
MAR2901CB 4-BIT, BIT-SLICE MICROPROCESSOR, CDIP40
相关代理商/技术参数
参数描述
M38002E4FS 制造商:Mitsubishi Electric 功能描述:8-BIT, UVPROM, 8 MHz, MICROCONTROLLER, CQCC64
M38002E4SP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER
M38002E4SS 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER
M38002E4-XXXFP 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER
M38002E4-XXXFS 制造商:MITSUBISHI 制造商全称:Mitsubishi Electric Semiconductor 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER