- 您现在的位置：买卖IC网 > PDF目录80396 > M38044M4-XXXFP 8-BIT, MROM, 8.4 MHz, MICROCONTROLLER, PQFP64 PDF资料下载
参数资料
| 型号： | M38044M4-XXXFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 8.4 MHz, MICROCONTROLLER, PQFP64 |
| 封装： | 14 X 14 MM, 0.80 MM PITCH, PLASTIC, QFP-64 |
| 文件页数： | 7/73页 |
| 文件大小： | 1882K |
| 代理商： | M38044M4-XXXFP |
第1页第2页第3页第4页第5页第6页当前第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页
Rev.4.01
Nov 14, 2003
page 15 of 136
3803/3804 Group
MISRG
(1) Bit 0 of address 001016: Oscillation stabilizing time set af-
ter STP instruction released bit
When the MCU stops the clock oscillation by the STP instruction
and the STP instruction has been released by an external interrupt
source, usually, the fixed values of Timer 1 and Prescaler 12
(Timer 1 = 0116, Prescaler 12 = FF16) are automatically reloaded
in order for the oscillation to stabilize. The user can inhibit the au-
tomatic setting by setting “1” to bit 0 of MISRG (address 001016).
However, by setting this bit to “1”, the previous values, set just be-
fore the STP instruction was executed, will remain in Timer 1 and
Prescaler 12. Therefore, you will need to set an appropriate value
to each register, in accordance with the oscillation stabilizing time,
before executing the STP instruction.
Figure 12 shows the structure of MISRG.
(2) Bits 1, 2, 3 of address 001016: Middle-speed Mode Auto-
matic Switch Function
In order to switch the clock mode of an MCU which has a sub-
clock, the following procedure is necessary:
set CPU mode register (003B16) --> start main clock oscillation -->
wait for oscillation stabilization --> switch to middle-speed mode
(or high-speed mode).
However, the 3803/3804 group has the built-in function which au-
tomatically switches from low to middle-speed mode either by the
SCL/SDA interrupt (only for the 3804 group) or by program.
qMiddle-speed mode automatic switch by SCL/SDA Interrupt
(only for 3804 group)
The SCL/SDA interrupt source enables an automatic switch when
the middle-speed mode automatic switch set bit (bit 1) of MISRG
(address 001016) is set to “1”. The conditions for an automatic
switch execution depend on the settings of bits 5 and 6 of the I2C
start/stop condition control register (address 001616). Bit 5 is the
SCL/SDA interrupt pin polarity selection bit and bit 6 is the SCL/
SDA interrupt pin selection bit. The main clock oscillation stabiliz-
ing time can also be selected by middle-speed mode automatic
switch wait time set bit (bit 2) of the MISRG.
qMiddle-speed mode automatic switch by program
The middle-speed mode can also be automatically switched by
program while operating in low-speed mode. By setting the
middle-speed automatic switch start bit (bit 3) of MISRG (address
001016) to “1” in the condition that the middle-speed mode auto-
matic switch set bit is “1” while operating in low-speed mode, the
MCU will automatically switch to middle-speed mode. In this case,
the oscillation stabilizing time of the main clock can be selected by
the middle-speed automatic switch wait time set bit (bit 2) of
MISRG (address 001016).
Fig.12 Structure of MISRG
MISRG
(MISRG : address 001016)
Oscillation stabilizing time set after STP instruction
released bit
Middle-speed mode automatic switch set bit
Middle-speed mode automatic switch wait time set bit
Middle-speed mode automatic switch start bit
(Depending on program)
Not used (return “0” when read)
(Do not write “1” to this bit)
b7
b0
0: Automatically set “0116” to Timer 1,
“FF16” to Prescaler 12
1: Automatically set disabled
0: Not set automatically
1: Automatic switching enabled (Notes 1, 2)
0: 4.5 to 5.5 machine cycles
1: 6.5 to 7.5 machine cycles
0: Invalid
1: Automatic switch start (Note 2)
Notes1: During operation in low-speed mode, it is possible automatically to
switch to middle-speed mode owing to SCL/SDA interrupt. This is
valid only for the 3804 group.
2: When automatic switch to middle-speed mode from low-speed mode
occurs, the values of CPU mode register (3B16) change.
相关PDF资料 |
PDF描述 |
|---|---|
| M37221M8-XXXSP | 8-BIT, MROM, 8.1 MHz, MICROCONTROLLER, PDIP42 |
| M30625MGP-XXXGP | 16-BIT, MROM, 24 MHz, MICROCONTROLLER, PQFP128 |
| M41T315Y-65MH6 | REAL TIME CLOCK, PDSO28 |
| MC9328MXLCVH15 | 150 MHz, RISC PROCESSOR, PBGA256 |
| MC9328MXLDVH20 | 200 MHz, RISC PROCESSOR, PBGA256 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M38049FFFP#U0 | 制造商:Renesas Electronics Corporation 功能描述: |
| M38049FFLHP#U0 | 制造商:Renesas Electronics Corporation 功能描述: |
| M38049RLSS | 功能描述:DEV EMULATOR CHIP RAM 2KB 64SDIP RoHS:否 类别:编程器，开发系统 >> 内电路编程器、仿真器以及调试器 系列:- 产品变化通告:Development Systems Discontinuation 19/Jul/2010 标准包装:1 系列:* 类型:* 适用于相关产品:* 所含物品:* |
| M3806 | 功能描述:电缆固定件和配件 LTSCG 625 BLACK RoHS:否 制造商:Heyco 类型:Cable Grips, Liquid Tight 材料:Nylon 颜色:Black 安装方法:Cable 最大光束直径:11.4 mm 抗拉强度: |
| M3806 BK001 | 制造商:Alpha Wire Company 功能描述:CBL 8COND 18AWG BLK 1000' |
发布紧急采购，3分钟左右您将得到回复。