- 您现在的位置：买卖IC网 > PDF目录67763 > M38049FFLWG 8-BIT, FLASH, 16.8 MHz, MICROCONTROLLER, PBGA64 PDF资料下载
参数资料
| 型号： | M38049FFLWG |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, FLASH, 16.8 MHz, MICROCONTROLLER, PBGA64 |
| 封装： | 6 X 6 MM, 0.65 MM PITCH, PLASTIC, LGA-64 |
| 文件页数： | 12/129页 |
| 文件大小： | 1721K |
| 代理商： | M38049FFLWG |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页当前第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页第83页第84页第85页第86页第87页第88页第89页第90页第91页第92页第93页第94页第95页第96页第97页第98页第99页第100页第101页第102页第103页第104页第105页第106页第107页第108页第109页第110页第111页第112页第113页第114页第115页第116页第117页第118页第119页第120页第121页第122页第123页第124页第125页第126页第127页第128页第129页
Rev.1.00
Oct 27, 2008
Page 109 of 128
REJ03B0266-0100
3804 Group (Spec.L)
NOTES ON PERIPHERAL FUNCTIONS
Notes on Input and Output Ports
1. Notes in standby state
In standby state*1 for low-power dissipation, do not make input
levels of an I/O port “undefined”. Even when an I/O port of N-
channel open-drain is set as output mode, if output data is “1”,
the aforementioned notes are necessary.
Pull-up (connect the port to VCC) or pull-down (connect the port
to VSS) these ports through a resistor.
When determining a resistance value, note the following points:
External circuit
Variation of output levels during the ordinary operation
When using built-in pull-up resistor, note on varied current
values:
When setting as an input port : Fix its input level
When setting as an output port : Prevent current from flowing
out to external
<Reason>
Exclusive input ports are always in a high-impedance state. An
output transistor becomes an OFF state when an I/O port is set as
input mode by the direction register, so that the port enter a high-
impedance state. At this time, the potential which is input to the
input buffer in a microcomputer is unstable in the state that input
levels are “undefined”. This may cause power source current.
Even when an I/O port of N-channel open-drain is set as output
mode by the direction register, if the contents of the port latch is
“1”, the same phenomenon as that of an input port will occur.
*1 Standby state :
stop mode by executing STP instruction
wait mode by executing WIT instruction
2. Modifying output data with bit managing instruction
When the port latch of an I/O port is modified with the bit
managing instruction*1, the value of the unspecified bit may be
changed.
<Reason>
I/O ports are set to input or output mode in bit units. Reading
from a port register or writing to it involves the following
operations.
Port in input mode
Read: Read the pin level.
Write: Write to the port latch.
Port in output mode
Read: Read the port latch or read the output from the peripheral
function (specifications differ depending on the port).
Write: Write to the port latch. (The port latch value is output
from the pin.)
Since bit managing instructions*1 are read-modify-write
instructions,*2 using such an instruction on a port register causes
a read and write to be performed simultaneously on the bits other
than the one specified by the instruction.
When an unspecified bit is in input mode, its pin level is read and
that value is written to the port latch. If the previous value of the
port latch differs from the pin level, the port latch value is changed.
If an unspecified bit is in output mode, the port latch is generally
read. However, for some ports the peripheral function output is
read, and the value is written to the port latch. In this case, if the
previous value of the port latch differs from the peripheral
function output, the port latch value is changed.
*1 Bit managing instructions: SEB and CLB instructions
*2 Read-modify-write instructions: Instructions that read memory
in byte units, modify the value, and then write the result to the
same location in memory in byte units
Termination of Unused Pins
1. Terminate unused pins
(1) Output ports : Open
(2) I/O ports :
Set the I/O ports for the input mode and connect them to VCC
or VSS through each resistor of 1 k
Ω to 10 kΩ.
Ports that permit the selecting of a built-in pull-up resistor can
also use this resistor. Set the I/O ports for the output mode and
open them at “L” or “H”.
When opening them in the output mode, the input mode of the
initial status remains until the mode of the ports is switched
over to the output mode by the program after reset. Thus, the
potential at these pins is undefined and the power source
current may increase in the input mode. With regard to an
effects on the system, thoroughly perform system evaluation
on the user side.
Since the direction register setup may be changed because of a
program runaway or noise, set direction registers by program
periodically to increase the reliability of program.
(3) The AVSS pin when not using the A/D converter :
When not using the A/D converter, handle a power source pin
for the A/D converter, AVSS pin as follows:
AVSS: Connect to the VSS pin.
2. Termination remarks
(1) I/O ports :
Do not open in the input mode.
<Reason>
The power source current may increase depending on the first-
stage circuit.
An effect due to noise may be easily produced as compared
with proper termination (2) in 1 and shown on the above.
(2) I/O ports :
When setting for the input mode, do not connect to VCC or VSS
directly.
<Reason>
If the direction register setup changes for the output mode
because of a program runaway or noise, a short circuit may occur
between a port and VCC (or VSS).
(3) I/O ports :
When setting for the input mode, do not connect multiple ports in
a lump to VCC or VSS through a resistor.
<Reason>
If the direction register setup changes for the output mode
because of a program runaway or noise, a short circuit may occur
between ports.
At the termination of unused pins, perform wiring at the
shortest possible distance (20 mm or less) from micro-
computer pins.
相关PDF资料 |
PDF描述 |
|---|---|
| M38049FFLHP | 8-BIT, FLASH, 16.8 MHz, MICROCONTROLLER, PQFP64 |
| M38049FFLSP | 8-BIT, FLASH, 16.8 MHz, MICROCONTROLLER, PDIP64 |
| M38112E4SS | 8-BIT, UVPROM, 4.19 MHz, MICROCONTROLLER, CDIP64 |
| M38112E4-XXXFP | 8-BIT, OTPROM, 4.19 MHz, MICROCONTROLLER, PQFP64 |
| M38112E4-XXXSP | 8-BIT, OTPROM, 4.19 MHz, MICROCONTROLLER, PDIP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M38049RLSS | 功能描述:DEV EMULATOR CHIP RAM 2KB 64SDIP RoHS:否 类别:编程器，开发系统 >> 内电路编程器、仿真器以及调试器 系列:- 产品变化通告:Development Systems Discontinuation 19/Jul/2010 标准包装:1 系列:* 类型:* 适用于相关产品:* 所含物品:* |
| M3806 | 功能描述:电缆固定件和配件 LTSCG 625 BLACK RoHS:否 制造商:Heyco 类型:Cable Grips, Liquid Tight 材料:Nylon 颜色:Black 安装方法:Cable 最大光束直径:11.4 mm 抗拉强度: |
| M3806 BK001 | 制造商:Alpha Wire Company 功能描述:CBL 8COND 18AWG BLK 1000' |
| M3806 BK002 | 制造商:Alpha Wire Company 功能描述:CBL 8COND 18AWG BLK 500' |
| M3806 BK005 | 制造商:Alpha Wire Company 功能描述:CBL 8COND 18AWG BLK 100' |
发布紧急采购，3分钟左右您将得到回复。