- 您现在的位置：买卖IC网 > PDF目录132980 > M38227M8HXXXFP 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP80 PDF资料下载
参数资料
| 型号： | M38227M8HXXXFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 4 MHz, MICROCONTROLLER, PQFP80 |
| 封装： | 14 X 20 MM, 0.80 MM PITCH, PLASTIC, QFP-80 |
| 文件页数： | 41/82页 |
| 文件大小： | 1168K |
| 代理商： | M38227M8HXXXFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页当前第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页第81页第82页
43
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
3822 Group
MITSUBISHI MICROCOMPUTERS
CLOCK GENERATING CIRCUIT
The 3822 group has two built-in oscillation circuits. An oscillation
circuit can be formed by connecting a resonator between XIN and
XOUT (XCIN and XCOUT). Use the circuit constants in accordance
with the resonator manufacturer's recommended values. No exter-
nal resistor is needed between XIN and XOUT since a feed-back
resistor exists on-chip. However, an external feed-back resistor is
needed between XCIN and XCOUT.
To supply a clock signal externally, input it to the XIN pin and make
the XOUT pin open. The sub-clock XCIN-XCOUT oscillation circuit
cannot directly input clocks that are externally generated. Accord-
ingly, be sure to cause an external resonator to oscillate.
Immediately after poweron, only the XIN oscillation circuit starts
oscillating, and XCIN and XCOUT pins function as I/O ports.
Frequency Control
(1) Middle-speed Mode
The internal clock
φ is the frequency of XIN divided by 8.
After reset, this mode is selected.
(2) High-speed Mode
The internal clock
φ is half the frequency of XIN.
(3) Low-speed Mode
qThe internal clock
φ is half the frequency of XCIN.
qA low-power consumption operation can be realized by stopping
the main clock XIN in this mode. To stop the main clock, set bit 5
of the CPU mode register to “1”.
When the main clock XIN is restarted, set enough time for oscil-
lation to stabilize by programming.
Note: If you switch the mode between middle/high-speed and low-
speed, stabilize both XIN and X CIN oscillations. The
sufficient time is required for the sub-clock to stabilize, es-
pecially immediately after poweron and at returning from
stop mode. When switching the mode between middle/high-
speed and low-speed, set the frequency on condition that
f(XIN) > 3f(XCIN).
Fig. 42 Ceramic resonator circuit
Fig. 43 External clock input circuit
Oscillation Control
(1) Stop Mode
If the STP instruction is executed, the internal clock
φ stops at an
“H” level, and XIN and XCIN oscillators stop. Timer 1 is set to
“FF16” and timer 2 is set to “0116”.
Either XIN or XCIN divided by 16 is input to timer 1 as count
source, and the output of timer 1 is connected to timer 2. The bits
of the timer 123 mode register except bit 4 are cleared to “0”. Set
the timer 1 and timer 2 interrupt enable bits to disabled (“0”) be-
fore executing the STP instruction. Oscillator restarts at reset or
when an external interrupt is received, but the internal clock
φ is
not supplied to the CPU until timer 2 underflows. This allows timer
for the clock circuit oscillation to stabilize.
(2) Wait Mode
If the WIT instruction is executed, the internal clock
φ stops at an
“H” level. The states of XIN and XCIN are the same as the state be-
fore the executing the WIT instruction. The internal clock restarts
at reset or when an interrupt is received. Since the oscillator does
not stop, normal operation can be started immediately after the
clock is restarted.
XCIN XCOUT
XIN
XOUT
CIN
COUT
CCIN
CCOUT
Rf
Rd
XIN
External oscillation circuit
Open
VCC
VSS
CCIN
CCOUT
Rf
Rd
XCIN
XCOUT
XOUT
相关PDF资料 |
PDF描述 |
|---|---|
| MPC603RZT200TX | 32-BIT, 200 MHz, RISC PROCESSOR, PBGA255 |
| MB90423GBPF | 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP100 |
| MC68HC705F6B/K | 8-BIT, OTPROM, MICROCONTROLLER, PDIP42 |
| MK2069-02GI | 160 MHz, OTHER CLOCK GENERATOR, PDSO56 |
| MC68882CFN16A | 32-BIT, MATH COPROCESSOR, PQCC68 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M38227RFS | 制造商:Renesas Electronics Corporation 功能描述:MCU - Trays |
| M3823 BK001 | 制造商:Alpha Wire Company 功能描述:CBL 30COND 18AWG BLK 1000' |
| M3823 BK002 | 制造商:Alpha Wire Company 功能描述:CBL 30COND 18AWG BLK 500' |
| M3823 BK005 | 制造商:Alpha Wire Company 功能描述:CBL 30COND 18AWG BLK 100' |
| M38234G4FP#U0 | 功能描述:MCU 2/5V 16K 80-QFP QZ-ROM RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 标准包装:250 系列:80C 核心处理器:8051 芯体尺寸:8-位 速度:16MHz 连通性:EBI/EMI，I²C，UART/USART 外围设备:POR，PWM，WDT 输入/输出数:40 程序存储器容量:- 程序存储器类型:ROMless EEPROM 大小:- RAM 容量:256 x 8 电压 - 电源 (Vcc/Vdd):4.5 V ~ 5.5 V 数据转换器:A/D 8x10b 振荡器型:内部 工作温度:-40°C ~ 85°C 封装/外壳:68-LCC（J 形引线） 包装:带卷 (TR) |
发布紧急采购，3分钟左右您将得到回复。