- 您现在的位置：买卖IC网 > PDF目录80568 > M38254M6DXXXFP 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP100 PDF资料下载
参数资料
| 型号： | M38254M6DXXXFP |
| 元件分类： | 微控制器/微处理器 |
| 英文描述： | 8-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP100 |
| 封装： | 14 X 20 MM, 0.65 MM PITCH, PLASTIC, QFP-100 |
| 文件页数： | 37/70页 |
| 文件大小： | 994K |
| 代理商： | M38254M6DXXXFP |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页当前第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
3825 Group
42
CLOCK GENERATING CIRCUIT
The 3825 group has two built-in oscillation circuits. An oscillation
circuit can be formed by connecting a resonator between XIN and
XOUT (XCIN and XCOUT). Use the circuit constants in accordance
with the resonator manufacturer's recommended values. No exter-
nal resistor is needed between XIN and XOUT since a feed-back
resistor exists on-chip. However, an external feed-back resistor is
needed between XCIN and XCOUT.
To supply a clock signal externally, input it to the XIN pin and make
the XOUT pin open. The sub-clock XCIN-XCOUT oscillation circuit
cannot directly input clocks that are externally generated. Accord-
ingly, be sure to cause an external resonator to oscillate.
Immediately after poweron, only the XIN oscillation circuit starts
oscillating, and XCIN and XCOUT pins function as I/O ports.
Frequency Control
(1) Middle-speed mode
The internal clock
φ is the frequency of XIN divided by 8.
After reset, this mode is selected.
(2)High-speed mode
The internal clock
φ is half the frequency of XIN.
(3) Low-speed mode
The internal clock φ is half the frequency of XCIN.
A low-power consumption operation can be realized by stopping
the main clock XIN in this mode. To stop the main clock, set bit 5
of the CPU mode register to “1”.
When the main clock XIN is restarted, set enough time for oscil-
lation to stabilize by programming.
Note: If you switch the mode between middle/high-speed and low-
speed, stabilize both XIN and XCIN oscillations. The suffi-
cient time is required for the sub-clock to stabilize, espe-
cially immediately after power-on and at returning from stop
mode. When switching the mode between middle/high-
speed and low-speed, set the frequency in the condition
that f(XIN) > 3f(XCIN).
Fig. 41 Ceramic resonator circuit
Fig. 42 External clock input circuit
Oscillation Control
(1) Stop mode
If the STP instruction is executed, the internal clock
φ stops at an
“H” level, and XIN and XCIN oscillators stop. Timer 1 is set to “FF16”
and timer 2 is set to “0116”.
Either XIN or XCIN divided by 16 is input to timer 1 as count
source, and the output of timer 1 is connected to timer 2.
The bits of the timer 123 mode register except bit 4 are cleared to
“0”. Set the timer 1 and timer 2 interrupt enable bits to disabled
(“0”) before executing the STP instruction.
Oscillator restarts at reset or when an external interrupt is re-
ceived, but the internal clock
φ is not supplied to the CPU until
timer 2 underflows. This allows time for the clock circuit oscillation
to stabilize.
(2) Wait mode
If the WIT instruction is executed, the internal clock
φ stops at an
“H” level. The states of XIN and XCIN are the same as the state be-
fore the executing the WIT instruction. The internal clock restarts
at reset or when an interrupt is received. Since the oscillator does
not stop, normal operation can be started immediately after the
clock is restarted.
XCIN
CIN
COUT
CCIN
CCOUT
Rf
Rd
XCOUT
XIN
XOUT
XIN
XOUT
External oscillation circuit
Open
VCC
VSS
CCIN
CCOUT
Rf
Rd
XCIN
XCOUT
相关PDF资料 |
PDF描述 |
|---|---|
| MAF8441P | 8-BIT, MROM, 6 MHz, MICROCONTROLLER, PDIP28 |
| M38064E8-XXXFP | 8-BIT, OTPROM, MICROCONTROLLER, PQFP80 |
| MAR2901CB | 4-BIT, BIT-SLICE MICROPROCESSOR, CDIP40 |
| MAQ17502LE | 16-BIT, MICROPROGRAM SEQUENCER, CQCC64 |
| MAS17502CB | 16-BIT, MICROPROGRAM SEQUENCER, CDIP64 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| M38257E8FP | 制造商:Renesas Electronics Corporation 功能描述:8-BIT, OTPROM, 4 MHz, MICROCONTROLLER, PQFP100 |
| M38257E8FS | 功能描述:IC 740 MCU OTP 32K 100-PQFP RoHS:是 类别:集成电路 (IC) >> 嵌入式 - 微控制器， 系列:740/38000 标准包装:160 系列:S08 核心处理器:S08 芯体尺寸:8-位 速度:40MHz 连通性:I²C，LIN，SCI，SPI 外围设备:LCD，LVD，POR，PWM，WDT 输入/输出数:53 程序存储器容量:32KB（32K x 8） 程序存储器类型:闪存 EEPROM 大小:- RAM 容量:1.9K x 8 电压 - 电源 (Vcc/Vdd):2.7 V ~ 5.5 V 数据转换器:A/D 12x12b 振荡器型:内部 工作温度:-40°C ~ 105°C 封装/外壳:64-LQFP 包装:托盘 |
| M38258MCM084 | 制造商:Panasonic Industrial Company 功能描述:IC |
| M3826 | 功能描述:电缆固定件和配件 LTRSCG 1000 BLACK RoHS:否 制造商:Heyco 类型:Cable Grips, Liquid Tight 材料:Nylon 颜色:Black 安装方法:Cable 最大光束直径:11.4 mm 抗拉强度: |
| M3826 BK001 | 制造商:Alpha Wire Company 功能描述:CBL 2COND 16AWG BLK 1000' |
发布紧急采购，3分钟左右您将得到回复。